Print Report | Back to Sample Detail

Sample Record for 2024-04-13-1

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 994903 DEA: 11430244 EFIS: 1118000033 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-125-9.3/13.0
Work Description: PLACE HMA, RHMA, SLAB REPLACEMENT, AND ELECTRICAL WORK.
Location Description: SAN DIEGO COUNTY IN AND NEAR LEMON GROVE FROM 0.3 MILE SOUTH OF ELKELTON PLACE UNDERCROSSING TO 0.2 MILE SOUTH OF ROUTE 125/94 SEPARATION
Contractor Name: HAZARD CONSTRUCTION ENGR LLC
Contractor Address: 10529 Vine Street, Lakeside, CA 92040
Resident Engineer: Sultan Ghazialam Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2024-04-13-1
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/13/2024
Date that the sample was received by the laboratory/organization performing the testing: 04/15/2024
The quantity of what the sample constitutes: 12 boxes
A brief description of the sample: 3/4" HMA PSU
From where was the sample collected: Source
Laboratory sample identification: 0109-PSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Otay

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number: 220817 Otay Val
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 8

Test Results

Test 1 of 8

DIME Test ID: 2024-04-13-1-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 05/14/2024
Date Tested: 04/18/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies within 4.7% target value range.
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 4027.5 g
Mass of the specimen and specimen basket assembly prior to ignition 6063.7 g
Mass of HMA Sample prior to ignition 2036.2 g
Corrected Asphalt Binder Content 5.09 %
Mass Loss 117.5 g
Mass of aggregate remaining after ignition 1918.7 g
Correction Factor (Percent by mass of HMA Specimen) 0.68 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 1000.4 F

Test 2 of 8

DIME Test ID: 2024-04-13-1-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 05/14/2024
Date Tested: 04/18/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies
Test Result Compliance: complies
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7477.1 grams
Mass of oven-dry sample in air for Sample 1 2521 grams
Mass of container filled with the sample and water for Sample 1 8997.6 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.52
Theoretical maximum density at 25°C (77°F) 2513 kg/m^3

Test 3 of 8

DIME Test ID: 2024-04-13-1-3
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 05/14/2024
Date Tested: 04/19/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies within 4% +/- 1.5
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 3.7 %
Percent Air Voids 2 4.1 %
Percent Air Voids 3 3.9 %
Average Percent Air Voids 3.9 %

Test 4 of 8

DIME Test ID: 2024-04-13-1-4
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 05/14/2024
Date Tested: 04/19/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Test results are within specification limits.
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.426
Bulk Specific Gravity 2 2.417
Bulk Specific Gravity 3 2.422
Average Bulk Specific Gravity 2.422

Test 5 of 8

DIME Test ID: 2024-04-13-1-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 05/14/2024
Date Tested: 04/24/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 207 psi
Average Wet Tensile Strength 410 psi
Tensile Strength Ratio 1.98

Test 6 of 8

DIME Test ID: 2024-04-13-1-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 05/14/2024
Date Tested: 04/24/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target <12.0
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 122 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) 15000
Stripping Inflection Point (Wheel B) 15000
Maximum impression at 5000 passes (left wheel) 2.19 mm
Maximum impression at 5000 passes (right wheel) 1.65 mm
Average impression at 5000 passes (left/right avg) 1.92 mm
Maximum impression at 10000 passes (left wheel) 2.4 mm
Maximum impression at 10000 passes (right wheel) 2.3 mm
Average impression at 10000 passes (left/right avg) 2.35 mm
Maximum impression at 15000 passes (left wheel) 3.03 mm
Maximum impression at 15000 passes (right wheel) 2.31 mm
Average impression at 15000 passes (left/right avg) 2.67 mm
Average impression at 20000 passes (left/right avg) no data
Average impression at 25000 passes (left/right avg) no data

Test 7 of 8

DIME Test ID: 2024-04-13-1-7
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 05/14/2024
Date Tested: 04/18/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: 3 RAP burns
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 4011.3 g
Mass of the specimen and specimen basket assembly prior to ignition 5519.8 g
Mass of HMA Sample prior to ignition 1508.5 g
Corrected Asphalt Binder Content 6.99 %
Mass Loss 105.5 g
Mass of aggregate remaining after ignition 1403 g
Correction Factor (Percent by mass of HMA Specimen) no data0 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 1000.4 F

Test 8 of 8

DIME Test ID: 2024-04-13-1-8
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 05/14/2024
Date Tested: 04/18/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: RAP Rice
Test Result Compliance: complies
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7477.1 grams
Mass of oven-dry sample in air for Sample 1 1546.9 grams
Mass of container filled with the sample and water for Sample 1 8383.6 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.416
Theoretical maximum density at 25°C (77°F) 2409 kg/m^3