Print Report | Back to Sample Detail

Sample Record for 2024-04-09-17

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 994733 DEA: 043Q5704 EFIS: 0419000225 QA Service Level: 1
DIST-CO-RTE-PM: 04-SF,-101,280-VAR
Work Description: STRENGTHEN GIRDER, CLEAN AND PAINT STRUCTURAL STEEL, & REPAIR DECK.
Location Description: THE CITY AND COUNTY OF SAN FRANCISCO AT VARIOUS LOCATIONS
Contractor Name: DISNEY CONSTRUCTION, INC.
Contractor Address: 533 airport Blvd, Suite 120, Burlingame, CA 94010
Resident Engineer: Marcus Washington Structure Rep.: Shahram Monem

Sample Information

DIME Sample ID: 2024-04-09-17
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Sacramento Field Office
Sample Organization Contact: (916) 2058871
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 04/09/2024
Date that the sample was received by the laboratory/organization performing the testing: 04/11/2024
The quantity of what the sample constitutes: 270
A brief description of the sample: ASTM A325 Bolts
From where was the sample collected: Fabricator
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: C&K Johnson Ind.

Material Information

Rocap Number(s): 415163503
Heat Number(s): 10815890
Nut Mfg. Lot Number(s):
Washer Mfg. Lot Number(s):
Bolt Specification: ASTM A325
Bolt Length(s): 4-1/2"
Nut Specification: ASTM A563
Washer Specification: ASTM F436
Finish: ASTM A153
Diameter/Size: 7/8-9 x 4-1/2
Bolt Mfg. Lot Number: E837I1
Rocap Test Requirement(s):
Lubricant Requirements(s):
Washer Inner Diameter(s):
Test results on following page(s): 5

Test Results

Test 1 of 5

DIME Test ID: 2024-04-09-17-1
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 04/19/2024
Date Tested: 04/16/2024
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Wedge Tensile
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
1AE837I10.875070158312.0810.00Wedge Tensileaauvinen
UTM 450kip
Temperature no data

Test 2 of 5

DIME Test ID: 2024-04-09-17-2
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 04/19/2024
Date Tested: 04/16/2024
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number E837I1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 LE USA
Size 0.875 in
Bolt Length 4.5 in
Gage Type Pass

Test 3 of 5

DIME Test ID: 2024-04-09-17-3
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 04/19/2024
Date Tested: 04/16/2024
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number E837I1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 LE USA
Size 0.875 in
Bolt Length 4.5 in
Gage Type Pass

Test 4 of 5

DIME Test ID: 2024-04-09-17-4
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/19/2024
Date Tested: 04/16/2024
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number E837I1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 LE USA
Size 0.875 in
Bolt Length 4.5 in
Measurement Average 3.16 mils

Test 5 of 5

DIME Test ID: 2024-04-09-17-5
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/19/2024
Date Tested: 04/16/2024
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number E837I1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 LE USA
Size 0.875 in
Bolt Length 4.5 in
Measurement Average 2.49 mils