Sample Record for 2023-12-18-29
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 215677 DEA: 044G0804 EFIS: 0412000332 COOP: 042676
QA Service Level: 1
DIST-CO-RTE-PM: 04-SOL-80-R10.4/30.2
Work Description: Highway widening, overhead signs, and electronic toll system.
Location Description: In Solano County in Fairfield and Vacaville from 1.0 mile west of Red Top Road Undercrossing to 0.4 mile east of Leisure Town Road Overcrossing.
Contractor Name: O.C. JONES & SONS, INC.
Contractor Address: 1520 Fourth Street, Berkeley, CA 94710
Resident Engineer: Justen Tatum Structure Rep.: Kelsey Littell
Sample Information
DIME Sample ID: 2023-12-18-29
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (213) 505-4213
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 12/18/2023
Date that the sample was received by the laboratory/organization performing the testing: 12/27/2023
The quantity of what the sample constitutes: 157
A brief description of the sample: Fastener Assembly
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Madison, IL
Material Information
Rocap Number(s):
Heat Number(s): 1000219814
5805160702
128069
Nut Mfg. Lot Number(s): 37644-5805160702
Washer Mfg. Lot Number(s): 1222-578
Bolt Specification: A325
Bolt Length(s): 2.5
Nut Specification: A563
Washer Specification: F436
Finish: MG
Diameter/Size: 7/8
Bolt Mfg. Lot Number: 38196-1000219814
Rocap Test Requirement(s):
Lubricant Requirements(s):
Washer Inner Diameter(s):
Test Results
Test 1 of 13
DIME Test ID: 2023-12-18-29-1
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test: Proof Load
Test Result Compliance:
Additional Comments When Verified:
|
Number of Samples
|
1
|
| Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By | | 1A | | | 75701 | | Proof Load | |
| |
|
UTM
|
450kip
|
|
Temperature
|
72 f
|
Test 2 of 13
DIME Test ID: 2023-12-18-29-2
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
38196-1000219814
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
0.875 in
|
|
Bolt Length
|
2.5 in
|
|
Gage Type
|
Pass
|
Test 3 of 13
DIME Test ID: 2023-12-18-29-3
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
38196-1000219814
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
0.875 in
|
|
Bolt Length
|
2.5 in
|
|
Gage Type
|
Pass
|
Test 4 of 13
DIME Test ID: 2023-12-18-29-5
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
38196-1000219814
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
0.875 in
|
|
Bolt Length
|
2.5 in
|
|
Measurement Average
|
2.58 mils
|
Test 5 of 13
DIME Test ID: 2023-12-18-29-6
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
38196-1000219814
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
0.875 in
|
|
Bolt Length
|
2.5 in
|
|
Measurement Average
|
2.8 mils
|
Test 6 of 13
DIME Test ID: 2023-12-18-29-7
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
37644-5805160702
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
U DH
|
|
Size
|
0.875 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
3.41 mils
|
Test 7 of 13
DIME Test ID: 2023-12-18-29-8
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
37644-5805160702
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
U DH
|
|
Size
|
0.875 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
3.84 mils
|
Test 8 of 13
DIME Test ID: 2023-12-18-29-9
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
1222-578
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
TSI F436
|
|
Size
|
0.875 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
2.6 mils
|
Test 9 of 13
DIME Test ID: 2023-12-18-29-10
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
1222-578
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
TSI F436
|
|
Size
|
0.875 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
2.96 mils
|
Test 10 of 13
DIME Test ID: 2023-12-18-29-11
Test Method: ASTM E18-20: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
1222-578
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
TSI F436
|
|
Size
|
0.875 in
|
|
Bolt Length
|
no data in
|
|
Hardness Reading Scale
|
C Scale
|
|
Hardness Reading Average
|
41.2
|
|
Spacing
|
Ok
|
Test 11 of 13
DIME Test ID: 2023-12-18-29-12
Test Method: ASTM E18-20: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
1222-578
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
TSI F436
|
|
Size
|
0.875 in
|
|
Bolt Length
|
no data in
|
|
Hardness Reading Scale
|
C Scale
|
|
Hardness Reading Average
|
41.4
|
|
Spacing
|
Ok
|
Test 12 of 13
DIME Test ID: 2023-12-18-29-13
Test Method: ASTM E18-20: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
38196-1000219814
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
0.875 in
|
|
Bolt Length
|
2.5 in
|
|
Hardness Reading Scale
|
C Scale
|
|
Hardness Reading Average
|
33.92
|
|
Spacing
|
Ok
|
Test 13 of 13
DIME Test ID: 2023-12-18-29-14
Test Method: ASTM E18-20: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/04/2024
Date Tested: 12/29/2023
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: brian.ellis@dot.ca.gov
Organization Phone: (916) 380-8623
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
38196-1000219814
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
0.875 in
|
|
Bolt Length
|
2.5 in
|
|
Hardness Reading Scale
|
C Scale
|
|
Hardness Reading Average
|
31.47
|
|
Spacing
|
Ok
|
