Print Report | Back to Sample Detail

Sample Record for 2023-07-11-87

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 994544 DEA: 023J8204 EFIS: 0222000087 QA Service Level: 1
DIST-CO-RTE-PM: 02-SIS-5-R19.0/R25.3
Work Description: COLD PLANE AC PAVEMENT AND PLACE RUBBERIZED HMA (GAP GRADED).
Location Description: SISKIYOU COUNTY IN AND NEAR WEED FROM 0.1 MILE SOUTH OF ROUTE 97 TO 0.1 MILE NORTH OF NORTH EDGEWOOD OVERHEAD
Contractor Name: J.F. SHEA CONSTRUCTION, INC.
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-07-11-87
TL Number from the TL Form: 897599
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Production Start-Up
Type of Material: Hot Mix Asphalt
Sample Taken Date: 07/11/2023
Date that the sample was received by the laboratory/organization performing the testing: 07/11/2023
The quantity of what the sample constitutes: Production Start-Up Evaluation
A brief description of the sample: Lime Treated 3/4-inch Type A HMA (eq. PG 64-28 M) with 23.6% RAP and virgin PG 58-34 M binder from Valero (Benicia, CA)
From where was the sample collected: Manufacturer
Laboratory sample identification: D79295
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: J.F. Shea Construction - Fawndale Rock and Asphalt (Redding, CA)

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number: JMF 22 11
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 7

Test Results

Test 1 of 7

DIME Test ID: 2023-07-11-87-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 11/16/2023
Date Tested: 08/15/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Pb≈4.44%
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 3015.8 g
Mass of the specimen and specimen basket assembly prior to ignition 5018.7 g
Mass of HMA Sample prior to ignition 2002.9 g
Corrected Asphalt Binder Content 4.44 %
Mass Loss 102.2 g
Mass of aggregate remaining after ignition 1900.7 g
Correction Factor (Percent by mass of HMA Specimen) 0.51 %
Moisture Content no data0 %
Temperature Compensation Factor 0.15 %
Test Temperature 538 C

Test 2 of 7

DIME Test ID: 2023-07-11-87-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 11/16/2023
Date Tested: 07/11/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Gmm=2.575
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7335.7 grams
Mass of oven-dry sample in air for Sample 1 2505.3 grams
Mass of container filled with the sample and water for Sample 1 8868.1 grams
Temperature of Water 77.2 °F
Specific Gravity for Sample 1 2.575
Theoretical maximum density at 25°C (77°F) 2568 kg/m^3

Test 3 of 7

DIME Test ID: 2023-07-11-87-3
Test Method: AASHTO T312-14: Preparing and Determining the Density of Asphalt Mixture Specimens by Means of the Superpave Gyratory Compactor (Method of Compaction)
Verified Date: 11/16/2023
Date Tested: 07/20/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: %Gmm8=84.3, %Gmm85=93.0, %Gmm130=94.1; Note: h130=120.2>115.0±5.0
Test Result Compliance: not applicable
Additional Comments When Verified:
Volume of the specimen (Vm8) 2370.308 cm^3
Volume of the specimen (Vm85) 2149.526 cm^3
Volume of the specimen (Vm130) 2123.032 cm^3
Uncorrected relative density (Gmmu8) 80.6 %
Uncorrected relative density (Gmmu85) 88.9 %
Uncorrected relative density (Gmmu130) 90 %
Relative density (Gmm8) 84.3 %
Relative density (Gmm85) 93 %
Relative density (Gmm130) 94.1 %
Air Voids (AV8) 15.7 %
Air Voids (AV85) 7 %
Air Voids (AV130) 5.9 %

Test 4 of 7

DIME Test ID: 2023-07-11-87-4
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 11/16/2023
Date Tested: 07/20/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Gmb=2.395
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk Specific Gravity 2.392
Bulk Specific Gravity 2 2.396
Bulk Specific Gravity 3 2.398
Average Bulk Specific Gravity 2.395

Test 5 of 7

DIME Test ID: 2023-07-11-87-5
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 11/16/2023
Date Tested: 07/20/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: AASHTO T 269: Pa=7.0%; MS-2: VMA=17.4%, VFA=60.0%, DP=0.9%
Test Result Compliance: does not comply
Additional Comments When Verified:
Percent Air Voids 7.1 %
Percent Air Voids 2 7 %
Percent Air Voids 3 6.9 %
Average Percent Air Voids 7 %

Test 6 of 7

DIME Test ID: 2023-07-11-87-6
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 11/16/2023
Date Tested: 08/08/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: S1=176, S2=164, TSR=93%
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 176 psi
Average Wet Tensile Strength 164 psi
Tensile Strength Ratio 0.93

Test 7 of 7

DIME Test ID: 2023-07-11-87-7
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 11/16/2023
Date Tested: 08/05/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: CT 389: Nf>15000, SIP>15000; CT 360: SA=0.3g/cm²
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 122 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) >15000
Stripping Inflection Point (Wheel B) >15000
Maximum impression at 5000 passes (left wheel) 1.31 mm
Maximum impression at 5000 passes (right wheel) 1.53 mm
Average impression at 5000 passes (left/right avg) 1.42 mm
Maximum impression at 10000 passes (left wheel) 1.63 mm
Maximum impression at 10000 passes (right wheel) 1.58 mm
Average impression at 10000 passes (left/right avg) 1.61 mm
Maximum impression at 15000 passes (left wheel) 1.79 mm
Maximum impression at 15000 passes (right wheel) 1.8 mm
Average impression at 15000 passes (left/right avg) 1.8 mm
Average impression at 20000 passes (left/right avg) no data
Average impression at 25000 passes (left/right avg) no data