Print Report | Back to Sample Detail

Sample Record for 2023-08-16-80

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 994722 DEA: 101P4804 EFIS: 1022000128 QA Service Level: 1
DIST-CO-RTE-PM: 10---
Work Description:
Location Description:
Contractor Name: George Reed Construction Inc
Contractor Address: 140 Empire Ave, Modesto, CA 95354
Resident Engineer: Troy Scheiber Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-08-16-80
TL Number from the TL Form: 1P48109
Sample Submitted By Organization: CT D10 - District 10 Materials Laboratory
Sample Organization Contact: (209) 948-7567
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 08/16/2023
Date that the sample was received by the laboratory/organization performing the testing: 08/18/2023
The quantity of what the sample constitutes: 4 boxes
A brief description of the sample: 1/2 HMA
From where was the sample collected: Manufacturer
Laboratory sample identification: 23-H-190
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: George Reed - Clements Plant

Material Information

HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number: 1
Sublot number: 9
HMA Mix Number: 23J004
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 2

Test Results

Test 1 of 2

DIME Test ID: 2023-08-16-80-1
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/25/2023
Date Tested: 08/25/2023
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Water
Specific Gravity for Sample 1 2.571
Theoretical maximum density at 25°C (77°F) 160 lb/ft^3

Test 2 of 2

DIME Test ID: 2023-08-16-80-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/25/2023
Date Tested: 08/25/2023
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of HMA Sample prior to ignition 1572.5 g
Corrected Asphalt Binder Content 5 %
Mass Loss 90.5 g
Correction Factor (Percent by mass of HMA Specimen) 0.57 %
Moisture Content no data0 %
Temperature Compensation Factor 0.19 %
Test Temperature 538 C