Print Report | Back to Sample Detail

Sample Record for 2023-08-22-27

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 994610 DEA: 112N1204 EFIS: 1121000149 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-8,15,67-VARIOUS
Work Description: MICRO-SURFACING, COLD PLANE, OVERLAY, STRIPING, & SHOULDER BACKING.
Location Description: SAN DIEGO COUNTY AT VARIOUS LOCATIONS
Contractor Name: PAVEMENT COATINGS CO.
Contractor Address: 10240 San Sevaine Way, Jurapa Valley, CA 91752
Resident Engineer: Michael Stewart Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-08-22-27
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 08/22/2023
Date that the sample was received by the laboratory/organization performing the testing: 08/23/2023
The quantity of what the sample constitutes: 12 boxes 3 bags
A brief description of the sample: 3/4" HMA PSU
From where was the sample collected: Source
Laboratory sample identification: 9301-PSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Otay

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number: 220817 Otay Val
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 7

Test Results

Test 1 of 7

DIME Test ID: 2023-08-22-27-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/01/2023
Date Tested: 08/28/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 4015.3 g
Mass of the specimen and specimen basket assembly prior to ignition 6092 g
Mass of HMA Sample prior to ignition 2076.7 g
Corrected Asphalt Binder Content 5.08 %
Mass Loss 117.1 g
Mass of aggregate remaining after ignition 1959.6 g
Correction Factor (Percent by mass of HMA Specimen) 0.56 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 F

Test 2 of 7

DIME Test ID: 2023-08-22-27-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 09/01/2023
Date Tested: 08/28/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7477.1 grams
Mass of oven-dry sample in air for Sample 1 2554.7 grams
Mass of container filled with the sample and water for Sample 1 9017 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.517
Theoretical maximum density at 25°C (77°F) 156.7 lb/ft^3

Test 3 of 7

DIME Test ID: 2023-08-22-27-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 09/01/2023
Date Tested: 08/28/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.43
Bulk Specific Gravity 2 2.42
Bulk Specific Gravity 3 2.422
Average Bulk Specific Gravity 2.424

Test 4 of 7

DIME Test ID: 2023-08-22-27-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 09/01/2023
Date Tested: 08/28/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 3.5 %
Percent Air Voids 2 3.9 %
Percent Air Voids 3 3.8 %
Average Percent Air Voids 3.7 %

Test 5 of 7

DIME Test ID: 2023-08-22-27-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 09/07/2023
Date Tested: 09/01/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 189 psi
Average Wet Tensile Strength 143 psi
Tensile Strength Ratio 0.76

Test 6 of 7

DIME Test ID: 2023-08-22-27-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 09/01/2023
Date Tested: 08/30/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 122 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) >15000
Stripping Inflection Point (Wheel B) >10000
Maximum impression at 5000 passes (left wheel) 1.79 mm
Maximum impression at 5000 passes (right wheel) 1.47 mm
Average impression at 5000 passes (left/right avg) 1.63 mm
Maximum impression at 10000 passes (left wheel) 2.48 mm
Maximum impression at 10000 passes (right wheel) 1.97 mm
Average impression at 10000 passes (left/right avg) 2.23 mm
Maximum impression at 15000 passes (left wheel) 3.76 mm
Maximum impression at 15000 passes (right wheel) 2.97 mm
Average impression at 15000 passes (left/right avg) 3.37 mm
Average impression at 20000 passes (left/right avg) no data
Average impression at 25000 passes (left/right avg) no data

Test 7 of 7

DIME Test ID: 2023-08-22-27-7
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/01/2023
Date Tested: 08/29/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Burn 3 RAP Samples
Test Result Compliance:
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 3966.8 g
Mass of the specimen and specimen basket assembly prior to ignition 5623.1 g
Mass of HMA Sample prior to ignition 1656.3 g
Corrected Asphalt Binder Content 6.67 %
Mass Loss 110.4 g
Mass of aggregate remaining after ignition 1545.9 g
Correction Factor (Percent by mass of HMA Specimen) no data0 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 F