Print Report | Back to Sample Detail

Sample Record for 2023-08-18-66

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214493 DEA: 07311704 EFIS: 0715000013 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-134-0.0/R13.3
Work Description: CONCRETE SLAB REPLACEMENT, HMA PAVING, ELECTRICAL AND LANDSCAPE WORK.
Location Description: LOS ANGELES COUNTY IN LOS ANGELES, BURBANK, GLENDALE AND PASADENA FROM ROUTE 101/134 SEPARATION TO JUNCTION OF ROUTE 210/710
Contractor Name: PETERSON-CHASE GENERAL ENGINEERING CONSTRUCTION, INC.
Contractor Address: 16351 Construction Circle West, Irvine, CA 92606-4414
Resident Engineer: David Ayala Vanegas Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-08-18-66
TL Number from the TL Form: 018900
Sample Submitted By Organization: CT D07 - Materials Field Laboratory, Unit 1953
Sample Organization Contact: (213) 817-0387
Type of Sample: Department Acceptance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 08/18/2023
Date that the sample was received by the laboratory/organization performing the testing: 08/22/2023
The quantity of what the sample constitutes: 750 Tons
A brief description of the sample: 1/2" RHMA-A 106836
From where was the sample collected: Manufacturer
Laboratory sample identification: 23-380
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: AAA-Irwindale

Material Information

HMA Type: RHMA-G
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 106836
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 2

Test Results

Test 1 of 2

DIME Test ID: 2023-08-18-66-1
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/24/2023
Date Tested: 08/23/2023
Submitted By Organization: CT D07 - Materials Field Laboratory, Unit 1953
Organization Address: 1940 South Workman Mill Road,
Organization City: Whittier
Organization State: CA
Organization Zipcode: 90601
Organization Email: chad.chotibhongs@dot.ca.gov
Organization Phone: (213) 407-6963
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7359.3 grams
Mass of oven-dry sample in air for Sample 1 1580 grams
Mass of container filled with the sample and water for Sample 1 8292.4 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.442
Theoretical maximum density at 25°C (77°F) 152 lb/ft^3

Test 2 of 2

DIME Test ID: 2023-08-18-66-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/24/2023
Date Tested: 08/23/2023
Submitted By Organization: CT D07 - Materials Field Laboratory, Unit 1953
Organization Address: 1940 South Workman Mill Road,
Organization City: Whittier
Organization State: CA
Organization Zipcode: 90601
Organization Email: chad.chotibhongs@dot.ca.gov
Organization Phone: (213) 407-6963
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4037.5 g
Mass of the specimen and specimen basket assembly prior to ignition 5548.3 g
Mass of HMA Sample prior to ignition 1510.8 g
Corrected Asphalt Binder Content 7.44 %
Mass Loss 115.8 g
Mass of aggregate remaining after ignition 1395 g
Correction Factor (Percent by mass of HMA Specimen) 0.22 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C