Print Report | Back to Sample Detail

Sample Record for 2023-06-07-82

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 993669 DEA: 112N1164 EFIS: 1121000145 QA Service Level: 1
DIST-CO-RTE-PM: 11-IMP-186-0.0/2.1
Work Description: COLD PLANE, SAMI, RHMA-G AND PAVEMENT MARKINGS
Location Description: IMPERIAL COUNTY AT ANDRADE FROM MEXICO BORDER TO ROUTE 186/8 SEPARATION
Contractor Name: HAZARD CONSTRUCTION ENGR, LLC
Contractor Address: 10529 VINE STREET, LAKESIDE, CA 92040
Resident Engineer: Daniel Hernandez Duarte Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-06-07-82
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 06/07/2023
Date that the sample was received by the laboratory/organization performing the testing: 06/09/2023
The quantity of what the sample constitutes: 16 boxes 12 bags
A brief description of the sample: 1/2" RHMA-G
From where was the sample collected: Supplier
Laboratory sample identification: 7404-PSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: API Gateway

Material Information

HMA Type: RHMA-G
HMA Grading: 1/2 inch
Lot number: 2
Sublot number: 1
HMA Mix Number: 41
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 10

Test Results

Test 1 of 10

DIME Test ID: 2023-06-07-82-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/07/2023
Date Tested: 06/22/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 4009.9 g
Mass of the specimen and specimen basket assembly prior to ignition 5573.6 g
Mass of HMA Sample prior to ignition 1563.7 g
Corrected Asphalt Binder Content 7.2 %
Mass Loss 109.1 g
Mass of aggregate remaining after ignition 1454.6 g
Correction Factor (Percent by mass of HMA Specimen) -0.22 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 F

Test 2 of 10

DIME Test ID: 2023-06-07-82-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/07/2023
Date Tested: 08/07/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed no data
Mass of container filled with water 1 7477.1 grams
Mass of oven-dry sample in air for Sample 1 1508.6 grams
Mass of container filled with the sample and water for Sample 1 8352.5 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.383
Theoretical maximum density at 25°C (77°F) 148.3 lb/ft^3

Test 3 of 10

DIME Test ID: 2023-06-07-82-4
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 08/07/2023
Date Tested: 08/07/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.287
Bulk Specific Gravity 2 2.28
Bulk Specific Gravity 3 2.281
Average Bulk Specific Gravity 2.283

Test 4 of 10

DIME Test ID: 2023-06-07-82-3
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 08/07/2023
Date Tested: 08/07/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 4 %
Percent Air Voids 2 4.3 %
Percent Air Voids 3 4.3 %
Average Percent Air Voids 4.2 %

Test 5 of 10

DIME Test ID: 2023-06-07-82-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 08/07/2023
Date Tested: 08/07/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 157 psi
Average Wet Tensile Strength 125 psi
Tensile Strength Ratio 0.8

Test 6 of 10

DIME Test ID: 2023-06-07-82-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 08/07/2023
Date Tested: 06/28/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 131 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) >25000
Stripping Inflection Point (Wheel B) >15000
Maximum impression at 5000 passes (left wheel) 0.28 mm
Maximum impression at 5000 passes (right wheel) 0.37 mm
Average impression at 5000 passes (left/right avg) 0.33 mm
Maximum impression at 10000 passes (left wheel) 0.42 mm
Maximum impression at 10000 passes (right wheel) 0.55 mm
Average impression at 10000 passes (left/right avg) 0.49 mm
Maximum impression at 15000 passes (left wheel) 0.55 mm
Maximum impression at 15000 passes (right wheel) 0.7 mm
Average impression at 15000 passes (left/right avg) 0.63 mm
Maximum impression at 20000 passes (left wheel) 0.65 mm
Maximum impression at 20000 passes (right wheel) 0.88 mm
Average impression at 20000 passes (left/right avg) 0.77 mm
Average impression at 25000 passes (left/right avg) 0.92 mm

Test 7 of 10

DIME Test ID: 2023-06-07-82-7
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 08/07/2023
Date Tested: 06/15/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Cores
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.175
Bulk Specific Gravity 2 2.162
Bulk Specific Gravity 3 2.171
Average Bulk Specific Gravity 2.169

Test 8 of 10

DIME Test ID: 2023-06-07-82-8
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/07/2023
Date Tested: 06/27/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: RAP
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7477.1 grams
Mass of oven-dry sample in air for Sample 1 1537.1 grams
Mass of container filled with the sample and water for Sample 1 8397.7 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.493
Theoretical maximum density at 25°C (77°F) 155.2 lb/ft^3

Test 9 of 10

DIME Test ID: 2023-06-07-82-9
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/07/2023
Date Tested: 06/29/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: RAP
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 4014.7 g
Mass of the specimen and specimen basket assembly prior to ignition 5526.1 g
Mass of HMA Sample prior to ignition 1511.4 g
Corrected Asphalt Binder Content 6.5 %
Mass Loss 98.3 g
Mass of aggregate remaining after ignition 1413.1 g
Correction Factor (Percent by mass of HMA Specimen) no data0 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 F

Test 10 of 10

DIME Test ID: 2023-06-07-82-10
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 08/07/2023
Date Tested: 06/27/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Cores 1A4
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.166