Print Report | Back to Sample Detail

Sample Record for 2023-05-15-63

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212498 DEA: 021H5204 EFIS: 0217000009 QA Service Level: 1
DIST-CO-RTE-PM: 02-SIS-3,263-48.5/49.7 - 49.41
Work Description: Roadway Rehabilitation
Location Description: 02-Sis-3, 263-R46.8/R48.0, 49.07/49.41
Contractor Name: Myers-Shea JV
Contractor Address: 45 Morrison Ave, Sacramento, CA 95838
Resident Engineer: Austin Henry Structure Rep.: Nicolas Jimenez

Sample Information

DIME Sample ID: 2023-05-15-63
TL Number from the TL Form: 815606
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Production Start-Up
Type of Material: Hot Mix Asphalt
Sample Taken Date: 05/15/2023
Date that the sample was received by the laboratory/organization performing the testing: 05/15/2023
The quantity of what the sample constitutes: Production Start-Up Evaluation
A brief description of the sample: 16 boxes of Treated 3/4-inch Type A HMA (eq. PG 64-28 M) with 23.6% RAP and virgin PG 58-34 M from Valero - Benicia
From where was the sample collected: Manufacturer
Laboratory sample identification: D79227
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: JF Shea Construction - Fawndale Rock and Asphalt - Redding, CA

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number:
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 7

Test Results

Test 1 of 7

DIME Test ID: 2023-05-15-63-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 06/05/2023
Date Tested: 05/30/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Pb=4.79%
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 3011.6 g
Mass of the specimen and specimen basket assembly prior to ignition 5019.2 g
Mass of HMA Sample prior to ignition 2007.6 g
Corrected Asphalt Binder Content 4.79 %
Mass Loss 106.3 g
Mass of aggregate remaining after ignition 1901.3 g
Correction Factor (Percent by mass of HMA Specimen) 0.35 %
Moisture Content no data0 %
Temperature Compensation Factor 0.15 %
Test Temperature 538 C

Test 2 of 7

DIME Test ID: 2023-05-15-63-2
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 06/05/2023
Date Tested: 05/15/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Gmm=2.577
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7335.7 grams
Mass of oven-dry sample in air for Sample 1 2522.4 grams
Mass of container filled with the sample and water for Sample 1 8879.2 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.577
Theoretical maximum density at 25°C (77°F) 2569.5 kg/m^3

Test 3 of 7

DIME Test ID: 2023-05-15-63-3
Test Method: AASHTO T312-14: Preparing and Determining the Density of Asphalt Mixture Specimens by Means of the Superpave Gyratory Compactor (Method of Compaction)
Verified Date: 06/05/2023
Date Tested: 06/05/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Volume of the specimen (Vm8) 2310.255 cm^3
Volume of the specimen (Vm85) 2089.474 cm^3
Volume of the specimen (Vm130) 2062.98 cm^3
Uncorrected relative density (Gmmu8) 82.7 %
Uncorrected relative density (Gmmu85) 91.5 %
Uncorrected relative density (Gmmu130) 92.6 %
Relative density (Gmm8) 86 %
Relative density (Gmm85) 95.1 %
Relative density (Gmm130) 96.4 %
Air Voids (AV8) 14 %
Air Voids (AV85) 4.9 %
Air Voids (AV130) 3.6 %

Test 4 of 7

DIME Test ID: 2023-05-15-63-4
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 06/05/2023
Date Tested: 05/16/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Gmb=2.459
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk Specific Gravity 2.449
Bulk Specific Gravity 2 2.461
Bulk Specific Gravity 3 2.465
Average Bulk Specific Gravity 2.458

Test 5 of 7

DIME Test ID: 2023-05-15-63-5
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 06/05/2023
Date Tested: 06/05/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Pa=4.6%
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 5 %
Percent Air Voids 2 4.5 %
Percent Air Voids 3 4.3 %
Average Percent Air Voids 4.6 %

Test 6 of 7

DIME Test ID: 2023-05-15-63-6
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 06/05/2023
Date Tested: 05/18/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: S1=126psi, S2=123psi, TSR=98%
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 126 psi
Average Wet Tensile Strength 123 psi
Tensile Strength Ratio 0.98

Test 7 of 7

DIME Test ID: 2023-05-15-63-7
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 07/15/2023
Date Tested: 07/12/2023
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Nf>15000
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 122 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) >15000
Stripping Inflection Point (Wheel B) >15000
Maximum impression at 5000 passes (left wheel) 1.36 mm
Maximum impression at 5000 passes (right wheel) 1.31 mm
Average impression at 5000 passes (left/right avg) 1.34 mm
Maximum impression at 10000 passes (left wheel) 1.51 mm
Maximum impression at 10000 passes (right wheel) 1.44 mm
Average impression at 10000 passes (left/right avg) 1.48 mm
Maximum impression at 15000 passes (left wheel) 1.62 mm
Maximum impression at 15000 passes (right wheel) 1.53 mm
Average impression at 15000 passes (left/right avg) 1.58 mm
Average impression at 20000 passes (left/right avg) no data
Average impression at 25000 passes (left/right avg) no data