Print Report | Back to Sample Detail

Sample Record for 2023-04-23-4

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 215666 DEA: 11430564 EFIS: 1119000015 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-67-R6.0/24.4
Work Description: COLD PLANE, RHMA OVERLAY AND HFST, AND INSTALL CHANNELIZERS.
Location Description: SAN DIEGO COUNTY NEAR LAKESIDE AND RAMONA FROM 0.2 MILE NORTH OF SAN DIEGO RIVER BRIDGE TO ROUTE 78
Contractor Name: ATP General Engineering
Contractor Address: 4211 Ponderosa Ave, Suite C, San Diego, CA 92123
Resident Engineer: Victor Mercado Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-04-23-4
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/23/2023
Date that the sample was received by the laboratory/organization performing the testing: 04/24/2023
The quantity of what the sample constitutes: 12 boxes 2 bags
A brief description of the sample: 3/4" HMA PSU
From where was the sample collected: Supplier
Laboratory sample identification: 23-7206-PSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Martin Marietta Lakeside

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number: 23417005
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 6

Test Results

Test 1 of 6

DIME Test ID: 2023-04-23-4-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 05/15/2023
Date Tested: 05/08/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 3966.7 g
Mass of the specimen and specimen basket assembly prior to ignition 5993.7 g
Mass of HMA Sample prior to ignition 2027 g
Corrected Asphalt Binder Content 5.28 %
Mass Loss 118.8 g
Mass of aggregate remaining after ignition 1908.2 g
Correction Factor (Percent by mass of HMA Specimen) 0.58 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 F

Test 2 of 6

DIME Test ID: 2023-04-23-4-2
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 05/15/2023
Date Tested: 05/08/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7358.3 grams
Mass of oven-dry sample in air for Sample 1 2533.7 grams
Mass of container filled with the sample and water for Sample 1 8856.7 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.447
Theoretical maximum density at 25°C (77°F) 152.3 lb/ft^3

Test 3 of 6

DIME Test ID: 2023-04-23-4-3
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 05/15/2023
Date Tested: 05/08/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 2.4 %
Percent Air Voids 2 2.5 %
Percent Air Voids 3 2.8 %
Average Percent Air Voids 2.6 %

Test 4 of 6

DIME Test ID: 2023-04-23-4-4
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 05/15/2023
Date Tested: 05/08/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.388
Bulk Specific Gravity 2 2.387
Bulk Specific Gravity 3 2.379
Average Bulk Specific Gravity 2.385

Test 5 of 6

DIME Test ID: 2023-04-23-4-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 05/15/2023
Date Tested: 05/08/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 228 psi
Average Wet Tensile Strength 133 psi
Tensile Strength Ratio 58.33

Test 6 of 6

DIME Test ID: 2023-04-23-4-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 05/15/2023
Date Tested: 05/08/2023
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 45.0 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) 25000
Stripping Inflection Point (Wheel B) 25000
Maximum impression at 5000 passes (left wheel) 1.75 mm
Maximum impression at 5000 passes (right wheel) 1.27 mm
Average impression at 5000 passes (left/right avg) 1.51 mm
Maximum impression at 10000 passes (left wheel) 2.36 mm
Maximum impression at 10000 passes (right wheel) 1.55 mm
Average impression at 10000 passes (left/right avg) 1.96 mm
Maximum impression at 15000 passes (left wheel) no data0 mm
Maximum impression at 15000 passes (right wheel) no data0 mm
Average impression at 15000 passes (left/right avg) no data0 mm
Average impression at 20000 passes (left/right avg) no data0 mm
Average impression at 25000 passes (left/right avg) no data0 mm