Print Report | Back to Sample Detail

Sample Record for 2023-04-14-19

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 994509 DEA: 101R4004 EFIS: 1023000140 QA Service Level: 1
DIST-CO-RTE-PM: 10-MER,MER/MER-5,59,152-22.6/32.5
Work Description:
Location Description:
Contractor Name: George Reed
Contractor Address: P.O. Box 4760, Modesto, CA 95352
Resident Engineer: Tofael Anwar Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-04-14-19
TL Number from the TL Form: 32238
Sample Submitted By Organization: CT D10 - District 10 Materials Laboratory
Sample Organization Contact: (209) 948-7567
Type of Sample: Quality Control
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/14/2023
Date that the sample was received by the laboratory/organization performing the testing: 04/17/2023
The quantity of what the sample constitutes: 4
A brief description of the sample: 3/4 HMA Type A
From where was the sample collected: Source
Laboratory sample identification: 23-H-044
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: George Reed Inc

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number: 2
Sublot number: 10
HMA Mix Number:
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 2

Test Results

Test 1 of 2

DIME Test ID: 2023-04-14-19-1
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 04/19/2023
Date Tested: 04/18/2023
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7424.2 grams
Mass of oven-dry sample in air for Sample 1 2550.5 grams
Mass of container filled with the sample and water for Sample 1 8934.7 grams
Temperature of Water 25 °F
Specific Gravity for Sample 1 2.452
Theoretical maximum density at 25°C (77°F) 152.6 lb/ft^3

Test 2 of 2

DIME Test ID: 2023-04-14-19-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/19/2023
Date Tested: 04/14/2023
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance: does not comply
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of HMA Sample prior to ignition 2051 g
Corrected Asphalt Binder Content 5.49 %
Mass Loss 126.1 g
Correction Factor (Percent by mass of HMA Specimen) 0.51 %
Moisture Content no data0 %
Temperature Compensation Factor 0.15 %
Test Temperature 1000 F