Print Report | Back to Sample Detail

Sample Record for 2022-07-06-49

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 993623 DEA: 022J3704 EFIS: 0221000071 QA Service Level: 1
DIST-CO-RTE-PM: 02-SHA-299-50.5/56.5,93.5/99.3
Work Description: ASPHALT RUBBER BINDER SEAL COAT, COLD PLANE AC PAVEMENT AND HMA.
Location Description: SHASTA COUNTY NEAR MONTGOMERY CREEK FROM 0.2 MILE WEST OF OAK POINT DRIVE TO OLD BERTAGNA PLACE AND FROM 0.1 MILE EAST OF SIERRA CENTER DRIVE TO LASSEN COUNTY LINE
Contractor Name: AMERICAN PAVEMENT SYSTEMS, INC.
Contractor Address: 1012 11th St., Modesto, CA 95354
Resident Engineer: Mike Zdenek Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2022-07-06-49
TL Number from the TL Form: 867305
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Department Acceptance
Type of Material: Asphalt Binder
Sample Taken Date: 07/06/2022
Date that the sample was received by the laboratory/organization performing the testing: 07/22/2022
The quantity of what the sample constitutes: 2 cans of binder
A brief description of the sample: PSE renewal
From where was the sample collected: Source
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Valero Benicia

Material Information

Performance Grade: PG 58-22
Modified:
Lot number:
Sublot number:
Tank number:
Time of sample:
HMA Supplier:
Certified Asphalt Supplier: Valero Marketing & Supply - Benicia CA
Multigrade: No
Multigrade Type:
Asphalt Binder Mix Number:
Test results on following page(s): 4

Test Results

Test 1 of 4

DIME Test ID: 2022-07-06-49-1
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 07/28/2022
Date Tested: 07/25/2022
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: OG
Test Result Compliance: complies
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.230 kPa
Phase Angle (δ) (for the 10 cycles) 84.2 degree
Complex Modulus (G*) (for the 10 measurements) 1.915 kPa
Test Temperature (Specimen 1) 58.0 C
Dynamic Shear, G*/sin(δ) 1.92 kPa

Test 2 of 4

DIME Test ID: 2022-07-06-49-2
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 07/28/2022
Date Tested: 07/25/2022
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.586 kPa
Phase Angle (δ) (for the 10 cycles) 77.8 degree
Complex Modulus (G*) (for the 10 measurements) 5.859 kPa
Test Temperature (Specimen 1) 58.0 C
Dynamic Shear, G*/sin(δ) 5.99 kPa

Test 3 of 4

DIME Test ID: 2022-07-06-49-3
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 07/28/2022
Date Tested: 07/26/2022
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: PAV
Test Result Compliance: complies
Additional Comments When Verified:
Phase PAV residue
Test Plate Diameter 8 mm
Test Gap 2 mm
Test Frequency 10.0 rad/s
Strain Amplitude 1.00 %
Stress Amplitude 20.155 kPa
Phase Angle (δ) (for the 10 cycles) 50.4 degree
Complex Modulus (G*) (for the 10 measurements) 2015.476 kPa
Test Temperature (Specimen 1) 22.0 C
(G*) x sin(δ)= 1553 kPa

Test 4 of 4

DIME Test ID: 2022-07-06-49-4
Test Method: AASHTO T313-19: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Verified Date: 07/28/2022
Date Tested: 07/28/2022
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Minimum test bath temperature at 240 s -12.1 C
Maximum test bath temperature at 240 s -11.9 C
Time of test load application no data HH:MM:SS
File name of test data no data
Time beam in bath no data
Time test started no data HH:MM:SS
Flags issued by software during test no data
Correlation coefficient (R²) no data0
Regression coefficient a no data
Regression coefficient b no data
Regression coefficient c no data
Load at time 0.0 no data0 mN
Deflection at time 0.0 s no data0 µm
Load at time 0.5 s no data0 mN
Deflection at time 0.5 s no data0 µm
Load at 60.0 s no data0 mN
Beam deflection 60.0 s no data0 µm
Measured Stiffness Modulus 60.0 s 87 mPa
Estimated Stiffness Modulus 60.0 s 86.8 mPa
Difference between stiffness moduli 60.0 s no data
Estimated m-value 60.0 s 0.397