Print Report | Back to Sample Detail

Sample Record for 2022-03-07-6

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 213811 DEA: 112T2184 EFIS: 1116000174 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-5-R38.4/R47.3
Work Description: (Alternative Delivery) Construct HOV lanes, soundwalls, culvert rehab, ITS, and bike trail on I-5 . NCC I-5 Highway Improvement.
Location Description: IN SAN DIEGO COUNTY IN ENCINITAS AND CARLSBAD FROM SAN ELIJO LAGOON BRIDGE TO 0.3 MILE NORTH OF PALOMAR AIRPORT ROAD OVERCROSSING.
Contractor Name: Flatiron-Skanska-Stacy and Witbeck, a Joint Venture
Contractor Address: 1525 Faraday Ave. #180, Carlsbad, CA 92008
Resident Engineer: Yong Pak Structure Rep.: Cailyn Le

Sample Information

DIME Sample ID: 2022-03-07-6
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 03/07/2022
Date that the sample was received by the laboratory/organization performing the testing: 03/08/2022
The quantity of what the sample constitutes: 3 bags, 12 boxes, 3 cans
A brief description of the sample: 1/2" HMA-A
From where was the sample collected: Job Site
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Otay

Material Information

HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number:
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 6

Test Results

Test 1 of 6

DIME Test ID: 2022-03-07-6-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/29/2024
Date Tested: 03/11/2022
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: 2T2184 2022-03-07-6-1
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly no data
Mass of the specimen and specimen basket assembly prior to ignition no data
Mass of HMA Sample prior to ignition 1560.3 g
Corrected Asphalt Binder Content 5.41 %
Mass Loss no data
Mass of aggregate remaining after ignition 1466.1 g
Correction Factor (Percent by mass of HMA Specimen) 0.63 %
Moisture Content no data0 %
Temperature Compensation Factor no data
Test Temperature 538 F

Test 2 of 6

DIME Test ID: 2022-03-07-6-2
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/29/2024
Date Tested: 03/10/2022
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: 2022-03-07-6-2 0523-PSU 11-2T2184
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7361.6 grams
Mass of oven-dry sample in air for Sample 1 1594.9 grams
Mass of container filled with the sample and water for Sample 1 8320.8 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.509
Theoretical maximum density at 25°C (77°F) no data

Test 3 of 6

DIME Test ID: 2022-03-07-6-3
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 08/29/2024
Date Tested: 03/10/2022
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: 0523-PSU 2022-03-07-9-3 11-2T2184
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 2.8 %
Percent Air Voids 2 2.5
Percent Air Voids 3 2.5
Average Percent Air Voids 2.6

Test 4 of 6

DIME Test ID: 2022-03-07-6-4
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 08/29/2024
Date Tested: 03/10/2022
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: 0523-PSU 2T2184 2022-03-07-06-4
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.439
Bulk Specific Gravity 2 2.446
Bulk Specific Gravity 3 2.447
Average Bulk Specific Gravity 2.444

Test 5 of 6

DIME Test ID: 2022-03-07-6-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 08/29/2024
Date Tested: 03/16/2022
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: 0523-PSU 11-2T2184
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 209 psi
Average Wet Tensile Strength 165 psi
Tensile Strength Ratio 79

Test 6 of 6

DIME Test ID: 2022-03-07-6-7
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/29/2024
Date Tested: 03/11/2022
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Oil Content Ignition Burn for RAP 0523-PSU 11-2T2184 2022-03-07-6-7
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly no data
Mass of the specimen and specimen basket assembly prior to ignition no data
Mass of HMA Sample prior to ignition 1560.3 g
Corrected Asphalt Binder Content 5.41 %
Mass Loss no data
Mass of aggregate remaining after ignition 1466.1 g
Correction Factor (Percent by mass of HMA Specimen) 0.63 %
Moisture Content no data0 %
Temperature Compensation Factor no data
Test Temperature 538 F