Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 215615 DEA: 101L2304 EFIS: 1020000163
QA Service Level: 1
DIST-CO-RTE-PM: 10-SJ-4-5.4/13.4
Work Description: COLD PLANE ASPHALT CONCRETE PAVEMENT AND RESURFACE WITH HMA AND RHMA.
Location Description: SAN JOAQUIN COUNTY NEAR STOCKTON FROM 1 MILE EAST OF MIDDLE RIVER BRIDGE TO 0.1 MILE WEST OF JOHN TURK ROAD
Contractor Name: GEORGE REED , INC.
Contractor Address: P.O. BOX 4760, MODESTO, CA 95352
Resident Engineer: Troy Scheiber Structure Rep.: Unknown
DIME Sample ID: 2021-09-12-3
TL Number from the TL Form: 21MC0005
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Department Acceptance
Type of Material: Asphalt Rubber Binder
Sample Taken Date: 09/12/2021
Date that the sample was received by the laboratory/organization performing the testing: 10/01/2021
The quantity of what the sample constitutes: 1 can
A brief description of the sample: Asphalt Rubber Binder
From where was the sample collected: Job Site
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: George Reed - Clements Plant
Asphalt modifier supplier:
Performance Grade: PG 64-16
Lot number: 1
Sublot number: 18
Asphalt Rubber Binder Mix Number:
DIME Test ID: 2021-09-12-3-1
Test Method: ASTM D217-16: Standard Test Methods for Cone Penetration of Lubricating Grease (Cone Penetration)
Verified Date: 10/06/2021
Date Tested: 10/06/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: 2018 per spec.
Test Result Compliance:
Additional Comments When Verified:
|
Determination
|
Unworked Penetration
|
|
Unworked Penetration
|
31 0.1 mm
|
DIME Test ID: 2021-09-12-3-2
Test Method: ASTM D36-14ε1: Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) (Softening Point)
Verified Date: 10/06/2021
Date Tested: 10/06/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: 2018 per spec.
Test Result Compliance:
Additional Comments When Verified:
|
ASTM Thermometer used?
|
C
|
|
Softening Point Sample 1
|
74 C
|
|
Softening Point Sample 2
|
74 C
|
|
Bath Liquid
|
USP glycerin
|
|
Minutes Reaction
|
no data
|
DIME Test ID: 2021-09-12-3-3
Test Method: ASTM D5329-16: Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements (Asphalt Pavement)
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
Data has not been verified.
