Print Report | Back to Sample Detail

Sample Record for 2026-09-28-14

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1001568 DEA: 033H51U4 EFIS: 0325000094 QA Service Level: 1
DIST-CO-RTE-PM: 03-NEV-49-R10.3/R13.8
Work Description: RDWY EXCAVATION, PLACE HMA, TRENCHLESS CULVERTS, AND RETAINING WALLS.
Location Description: NEVADA COUNTY NEAR GRASS VALLEY FROM 0.2 MILE SOUTH OF LA BARR MEADOWS ROAD TO 0.1 MILE NORTH OF SOUTH GRASS VALLEY OVERCROSSING
Contractor Name: GRANITE CONSTRUCTION
Contractor Address: 4001 BRADSHAW ROAD, SACRAMENTO, CA 95827
Resident Engineer: Renee Plaza Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2026-09-28-14
TL Number from the TL Form:
Sample Submitted By Organization: NV5 - Nevada City
Sample Organization Contact: (530) 362-0173
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 09/28/2026
Date that the sample was received by the laboratory/organization performing the testing: 09/29/2026
The quantity of what the sample constitutes: 2 boxes HMA
A brief description of the sample: Lot 1, sub lot 7, 2 boxes HMA for oil content
From where was the sample collected: Supplier
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Granite Bradshaw

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number:
Binder content (%): 0.0
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 2

Test Results

Test

DIME Test ID: 2026-09-28-14-1
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 10/01/2026
Date Tested: 09/30/2026
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7402.5 grams
Mass of oven-dry sample in air for Sample 1 2657.4 grams
Mass of container filled with the sample and water for Sample 1 9040.8 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.608
Theoretical maximum density at 25°C (77°F) 2600.4 kg/m^3

Test

DIME Test ID: 2026-09-28-14-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 10/01/2026
Date Tested: 09/30/2026
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: R1 OBC 4.6%
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of HMA Sample prior to ignition 2155.5 g
Corrected Asphalt Binder Content 4.78 %
Mass Loss 117.3 g
Correction Factor (Percent by mass of HMA Specimen) 0.66 %
Moisture Content no data0 %
Temperature Compensation Factor 0.02 %
Test Temperature 538 C