Print Report | Back to Sample Detail

Sample Record for 2017-04-20-26

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

DEA: No Project QA Service Level:
DIST-CO-RTE-PM: ---
Work Description: Special project identifier for material not associated with a project
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2017-04-20-26
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Quality Control
Type of Material: Reclaimed Asphalt Pavement
Sample Taken Date: 04/20/2017
Date that the sample was received by the laboratory/organization performing the testing: 04/20/2017
The quantity of what the sample constitutes: Mix Design
A brief description of the sample: Combined RAP
From where was the sample collected: Manufacturer
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Tullis Inc - Northstate Asphalt - Redding, CA

Material Information

RAP Source: Northstate Asphalt
Aggregate Size: Unknown
Aggregate Source: Unknown
RAP Stockpile: Static
Stockpile Size (tons): Unknown
Reclaimed Asphalt Pavement Mix Number:
Test results on following page(s): 2

Test Results

Test

DIME Test ID: 2017-04-20-26-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 03/22/2018
Date Tested: 04/20/2017
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Data input by Ward Jenkins for PEI during beta.
Test Result Compliance:
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of HMA Sample prior to ignition no data
Corrected Asphalt Binder Content 5.87 %
Mass Loss no data
Correction Factor (Percent by mass of HMA Specimen) no data
Moisture Content no data
Temperature Compensation Factor no data
Test Temperature no data

Test

DIME Test ID: 2017-04-20-26-2
Test Method: AASHTO T30-15: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Verified Date: 03/22/2018
Date Tested: 04/20/2017
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Data input by Ward Jenkins for PEI during beta. 1/4 in. sieve value is speculative.
Test Result Compliance:
Additional Comments When Verified:
Cumulative percent passing the 2 in. sieve no data
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 96.8 %
Cumulative percent passing the 3/8 in. sieve 89.9 %
Cumulative percent passing the 1/4 in. sieve 78.5 %
Cumulative percent passing the #4 sieve 67.1 %
Cumulative percent passing the #8 sieve 49.3 %
Cumulative percent passing the #16 sieve 35.9 %
Cumulative percent passing the #30 sieve 25.3 %
Cumulative percent passing the #50 sieve 18.6 %
Cumulative percent passing the #100 sieve 13.4 %
Cumulative percent passing the #200 sieve 9.8 %