Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 1001213 DEA: 11431644 EFIS: 1122000232
QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-78-N17.7
Work Description: Cold plane, RHMA overlay, Concrete Barriers, Landscape and Electrical.
Location Description: IN SAN DIEGO COUNTY FROM ROUTE 78/5 SEPARATION TO 0.3 MILE EAST OF ESCONDIDO BOULEVARD UNDERCROSSING.
Contractor Name: Skanska USA Civil West
Contractor Address: 1995 Agua Mansa Rd., Riverside, CA 92509
Resident Engineer: Yong Pak Structure Rep.: Carlos Lopez
DIME Sample ID: 2026-06-22-41
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 06/22/2026
Date that the sample was received by the laboratory/organization performing the testing: 06/23/2026
The quantity of what the sample constitutes: 4 boxes
A brief description of the sample: Plant Sample
From where was the sample collected: Supplier
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: RJ Noble Corona
HMA Type: RHMA-G
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number: 49R003ARSPW
Binder content (%): 7.5
Virgin binder PG: PG 64-16
Design binder PG: PG 64-16
Binder Supplier: World Oil
RAP content (%): 0
WMA Additives: Yes
Antistrip type:
DIME Test ID: 2026-06-22-41-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 07/06/2026
Date Tested: 07/02/2026
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Target 7.5%
Actual 7.89% Oven# 3
Test Result Compliance: complies
Additional Comments When Verified:
|
What temperature unit is used?
|
Fahrenheit
|
|
Test procedure used?
|
Method A
|
|
Mass of the specimen basket assembly
|
3923.7 g
|
|
Mass of the specimen and specimen basket assembly prior to ignition
|
5956.9 g
|
|
Mass of HMA Sample prior to ignition
|
2033.2 g
|
|
Corrected Asphalt Binder Content
|
7.89 %
|
|
Mass Loss
|
172.4 g
|
|
Mass of aggregate remaining after ignition
|
1860.8 g
|
|
Correction Factor (Percent by mass of HMA Specimen)
|
0.59 %
|
|
Moisture Content
|
no data0 %
|
|
Temperature Compensation Factor
|
no data0 %
|
|
Test Temperature
|
538 F
|
DIME Test ID: 2026-06-22-41-3
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 07/08/2026
Date Tested: 07/06/2026
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Verify Eddie's RICE of 2.402. Target 2.426. Rice Verified Re-tested at 2.412 Gmm
Test Result Compliance: not applicable
Additional Comments When Verified:
|
Number of tests
|
1
|
|
What is the unit of measurement for theoretical density?
|
US Units
|
|
Mass Determination
|
Air
|
|
Method Performed
|
Mechanical Agitation - Method A
|
|
Mass of container filled with water
|
7475.6 grams
|
|
Mass of oven-dry sample in air for Sample 1
|
2528 grams
|
|
Mass of container filled with the sample and water for Sample 1
|
8955.6 grams
|
|
Temperature of Water
|
77 °F
|
|
Specific Gravity for Sample 1
|
2.412
|
|
Theoretical maximum density at 25°C (77°F)
|
150.1 lb/ft^3
|
DIME Test ID: 2026-06-22-41-4
Test Method: CTM 375-February 2012: Determining the Density and Relative Compaction of Data Cores (lab)
Verified Date: 07/09/2026
Date Tested: 07/09/2026
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: COMPLIES
Test Result Compliance: complies
Additional Comments When Verified:
|
Number of Cores
|
3
|
|
Core ID
|
6A53
|
|
Dry Weight
|
1071.6 grams
|
|
Parrafin Coated Weight
|
1088 grams
|
|
Coated Weight in Water
|
599.8 grams
|
|
Theoretical Maximum Density
|
2.412
|
|
Core 2 ID
|
6B53
|
|
Dry Weight 2
|
1040.4 grams
|
|
Parrafin Coated Weight 2
|
1055.2 grams
|
|
Coated Weight in Water 2
|
582.8 grams
|
|
Core 3 ID
|
6C53
|
|
Dry Weight 3
|
1036.5 grams
|
|
Parrafin Coated Weight 3
|
1053.5 grams
|
|
Coated Weight in Water 3
|
571.4 grams
|
DIME Test ID: 2026-06-22-41-5
Test Method: CTM 375-February 2012: Determining the Density and Relative Compaction of Data Cores (lab)
Verified Date: 07/09/2026
Date Tested: 07/09/2026
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: COMPLIES
Test Result Compliance: complies
Additional Comments When Verified:
|
Number of Cores
|
3
|
|
Core ID
|
6A54
|
|
Dry Weight
|
1107.2 grams
|
|
Parrafin Coated Weight
|
1127.1 grams
|
|
Coated Weight in Water
|
609.3 grams
|
|
Theoretical Maximum Density
|
2.412
|
|
Core 2 ID
|
6B54
|
|
Dry Weight 2
|
1035.9 grams
|
|
Parrafin Coated Weight 2
|
1058.5 grams
|
|
Coated Weight in Water 2
|
570.1 grams
|
|
Core 3 ID
|
6C54
|
|
Dry Weight 3
|
1069.1 grams
|
|
Parrafin Coated Weight 3
|
1085.9 grams
|
|
Coated Weight in Water 3
|
589.8 grams
|
