Print Report | Back to Sample Detail

Sample Record for 2026-06-15-13

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1001669 DEA: 09379004 EFIS: 0919000004 QA Service Level: 1
DIST-CO-RTE-PM: 09-INY-395-R65.0/76.0
Work Description: FULL DEPTH RECYCLING, COLD PLANE, HMA AND CURB RAMPS.
Location Description: INYO COUNTY AT AND NEAR INDEPENDENCE FROM 3 MILES SOUTH OF MANZANAR REWARD ROAD TO 0.3 MILE NORTH OF SHABBELL LANE
Contractor Name: ROAD AND HIGHWAY BUILDERS LLC
Contractor Address: 950 E MUSTANG RD, SPARKS NV 89434
Resident Engineer: Garrett Rottner Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2026-06-15-13
TL Number from the TL Form:
Sample Submitted By Organization: CT D09 - Bishop Field Laboratory
Sample Organization Contact: (760) 872-5211
Type of Sample: Acceptance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 06/15/2026
Date that the sample was received by the laboratory/organization performing the testing: 06/15/2026
The quantity of what the sample constitutes: 8 boxes of 3/4" Type A HMA with RAP
A brief description of the sample: 750 - 1500 tons for today
From where was the sample collected: Job Site
Laboratory sample identification: HMA - 10
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Grinding Rock - Independence

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number: 1
Sublot number: 10
HMA Mix Number:
Binder content (%): 0.0
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 3

Test Results

Test

DIME Test ID: 2026-06-15-13-1
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 06/22/2026
Date Tested: 06/16/2026
Submitted By Organization: CT D09 - Bishop Field Laboratory
Organization Address: 500 South Main Street,
Organization City: Bishop
Organization State: CA
Organization Zipcode: 93514
Organization Email: chris.talbot@dot.ca.gov
Organization Phone: (760) 872-0794
General Comments for this Test: HMA-10
Test Result Compliance: complies
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7310.5 grams
Mass of oven-dry sample in air for Sample 1 2095.1 grams
Mass of container filled with the sample and water for Sample 1 8560.4 grams
Temperature of Water 76.8 °F
Specific Gravity for Sample 1 2.479
Theoretical maximum density at 25°C (77°F) 154.3 lb/ft^3

Test

DIME Test ID: 2026-06-15-13-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 06/22/2026
Date Tested: 06/16/2026
Submitted By Organization: CT D09 - Bishop Field Laboratory
Organization Address: 500 South Main Street,
Organization City: Bishop
Organization State: CA
Organization Zipcode: 93514
Organization Email: chris.talbot@dot.ca.gov
Organization Phone: (760) 872-0794
General Comments for this Test: HMA-10
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4255.6 g
Mass of the specimen and specimen basket assembly prior to ignition 6542.1 g
Mass of HMA Sample prior to ignition 2286.5 g
Corrected Asphalt Binder Content 4.61 %
Mass Loss 115.5 g
Mass of aggregate remaining after ignition 2171 g
Correction Factor (Percent by mass of HMA Specimen) 0.44 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C

Test

DIME Test ID: 2026-06-15-13-3
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Verified Date: 06/22/2026
Date Tested: 06/16/2026
Submitted By Organization: CT D09 - Bishop Field Laboratory
Organization Address: 500 South Main Street,
Organization City: Bishop
Organization State: CA
Organization Zipcode: 93514
Organization Email: chris.talbot@dot.ca.gov
Organization Phone: (760) 872-0794
General Comments for this Test: HMA-10 PP Gradation
Test Result Compliance: complies
Additional Comments When Verified:
Is an aggregate correction factor used? Yes
Aggregate correction factor for the 2 in. sieve (% passing) no data0 %
Aggregate correction factor for the 1 1/2 in. sieve (% passing) no data0 %
Aggregate correction factor for the 1 in. sieve (% passing) no data0 %
Aggregate correction factor for the 3/4 in. sieve (% passing) -1 %
Aggregate correction factor for the 1/2 in. sieve (% passing) -0.2 %
Aggregate correction factor for the 3/8 in. sieve (% passing) -0.3 %
Aggregate correction factor for the #4 sieve (% passing) -1.1 %
Aggregate correction factor for the #8 sieve (% passing) -1.2 %
Aggregate correction factor for the #16 sieve (% passing) -0.9 %
Aggregate correction factor for the #30 sieve (% passing) -0.7 %
Aggregate correction factor for the #50 sieve (% passing) -0.5 %
Aggregate correction factor for the #100 sieve (% passing) -0.2 %
Aggregate correction factor for the #200 sieve (% passing) -0.1 %
Cumulative percent passing the 2 in. sieve 100 %
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 95 %
Cumulative percent passing the 1/2 in. sieve 84 %
Cumulative percent passing the 3/8 in. sieve 75 %
Cumulative percent passing the #4 sieve 47 %
Cumulative percent passing the #8 sieve 32 %
Cumulative percent passing the #16 sieve 22 %
Cumulative percent passing the #30 sieve 16 %
Cumulative percent passing the #50 sieve 11 %
Cumulative percent passing the #100 sieve 8 %
Cumulative percent passing the #200 sieve 5 %