Print Report | Back to Sample Detail

Sample Record for 2026-03-27-38

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1000269 DEA: 070W6604 EFIS: 0722000360 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-47,110,405,605-Var
Work Description: METHACRYLATE, POLYESTER OVERLAY AND JOINT SEALS.
Location Description: LOS ANGELES COUNTY AT VARIOUS LOCATIONS
Contractor Name: VELARDE CONCRETE CONSTRUCTION, INC
Contractor Address: Unknown
Resident Engineer: Joahnna Vergara Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2026-03-27-38
TL Number from the TL Form: 032726
Sample Submitted By Organization: CT D07 - Materials Field Laboratory, Unit 1953
Sample Organization Contact: (213) 817-0387
Type of Sample: Acceptance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 03/27/2026
Date that the sample was received by the laboratory/organization performing the testing: 04/02/2026
The quantity of what the sample constitutes: 750 Tons
A brief description of the sample: 3/8 HMA-A
From where was the sample collected: Manufacturer
Laboratory sample identification: 26-076
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: AAA-Irwindale

Material Information

HMA Type: Type A HMA
HMA Grading: 3/8 inch
Lot number:
Sublot number:
HMA Mix Number: 109726
Binder content (%): 0.0
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 2

Test Results

Test

DIME Test ID: 2026-03-27-38-1
Test Method: AASHTO T209-25: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 04/06/2026
Date Tested: 04/03/2026
Submitted By Organization: CT D07 - Materials Field Laboratory, Unit 1953
Organization Address: 1940 South Workman Mill Road,
Organization City: Whittier
Organization State: CA
Organization Zipcode: 90601
Organization Email: chad.chotibhongs@dot.ca.gov
Organization Phone: (213) 407-6963
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed no data
Mass of container filled with water 1 7349.5 grams
Mass of oven-dry sample in air for Sample 1 1552.1 grams
Mass of container filled with the sample and water for Sample 1 8281.7 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.504
Theoretical maximum density at 25°C (77°F) 155.9 lb/ft^3

Test

DIME Test ID: 2026-03-27-38-2
Test Method: AASHTO T308-25: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/06/2026
Date Tested: 04/03/2026
Submitted By Organization: CT D07 - Materials Field Laboratory, Unit 1953
Organization Address: 1940 South Workman Mill Road,
Organization City: Whittier
Organization State: CA
Organization Zipcode: 90601
Organization Email: chad.chotibhongs@dot.ca.gov
Organization Phone: (213) 407-6963
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4094.3 g
Mass of the specimen and specimen basket assembly prior to ignition 5664.3 g
Corrected Asphalt Binder Content 5.73 %
Mass of HMA Sample prior to ignition 1570 g
Mass Loss 94.7 g
Mass of aggregate remaining after ignition 1475.3 g
Correction Factor (Percent by mass of HMA Specimen) 0.3 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C