Print Report | Back to Sample Detail

Sample Record for 2025-11-04-53

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1001127 DEA: 112N2064 EFIS: 1123000285 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-94-1.6/R13.3
Work Description: POLYESTER CONCRETE, METHACRYLATE, JOINT SEALS AND APPROACH SLABS.
Location Description: SAN DIEGO COUNTY AT VARIOUS LOCATIONS FROM 22ND STREET OVERCROSSING TO AVOCADO BOULEVARD OVERCROSSING
Contractor Name: TRUESDELL CORPORATION OF CALIFORNIA, INC.
Contractor Address: Unknown, 1310 west 23 st Tempe Arixzona 85282
Resident Engineer: fahad masud Structure Rep.: Tyler Jones

Sample Information

DIME Sample ID: 2025-11-04-53
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 11/04/2025
Date that the sample was received by the laboratory/organization performing the testing: 11/05/2025
The quantity of what the sample constitutes: 4 boxes
A brief description of the sample: Plant Sample
From where was the sample collected: Supplier
Laboratory sample identification: 25-11-03-55
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Martin Marietta

Material Information

HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 21217105 MM
Binder content (%): 0.0
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 3

Test Results

Test 1 of 3

DIME Test ID: 2025-11-04-53-1
Test Method: AASHTO T308-25: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 12/03/2025
Date Tested: 11/26/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: does not comply
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4038.1 g
Mass of the specimen and specimen basket assembly prior to ignition 5600.4 g
Corrected Asphalt Binder Content 6.14 %
Mass of HMA Sample prior to ignition 1562.3 g
Mass Loss 96.7 g
Mass of aggregate remaining after ignition 1465.6 g
Correction Factor (Percent by mass of HMA Specimen) 0.05 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C

Test 2 of 3

DIME Test ID: 2025-11-04-53-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 12/03/2025
Date Tested: 11/26/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7475.6 grams
Mass of oven-dry sample in air for Sample 1 1517.6 grams
Mass of container filled with the sample and water for Sample 1 8383.9 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.491
Theoretical maximum density at 25°C (77°F) 2484 kg/m^3

Test 3 of 3

DIME Test ID: 2025-11-04-53-3
Test Method: AASHTO T308-25: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 12/03/2025
Date Tested: 12/02/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Retest
Test Result Compliance: does not comply
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly 4023.5 g
Mass of the specimen and specimen basket assembly prior to ignition 5577.1 g
Corrected Asphalt Binder Content 6.24 %
Mass of HMA Sample prior to ignition 1553.6 g
Mass Loss 97.7 g
Mass of aggregate remaining after ignition 1455.9 g
Correction Factor (Percent by mass of HMA Specimen) 0.05 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 F