Print Report | Back to Sample Detail

Sample Record for 2025-10-22-60

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1001120 DEA: 033G6204 EFIS: 0325000037 QA Service Level: 1
DIST-CO-RTE-PM: 03-YOL-5-R22.8/R28.9
Work Description: COLD PLANE AC PVMT AND HMA (TYPE A).
Location Description: YOLO COUNTY NEAR DUNNIGAN FROM 0.2 MILE NORTH OF ROUTE 505/5 SEPARATION TO THE COLUSA COUNTY LINE
Contractor Name: ALL-AMERICAN CONSTRUCTION, INC.
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2025-10-22-60
TL Number from the TL Form:
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 10/22/2025
Date that the sample was received by the laboratory/organization performing the testing: 11/06/2025
The quantity of what the sample constitutes: 14 Boxes
A brief description of the sample: 3/4" HMA w/ 15% RAP
From where was the sample collected: Source
Laboratory sample identification: 10K 25-245
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert Woodland

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number: 1
Sublot number: 17
HMA Mix Number: 30640432407V
Binder content (%): 4.7
Virgin binder PG:
Design binder PG: PG 64-16
Binder Supplier: Valero
RAP content (%): 15
WMA Additives: No
Antistrip type:
Test results on following page(s): 3

Test Results

Test 1 of 3

DIME Test ID: 2025-10-22-60-1
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 11/21/2025
Date Tested: 11/07/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7402.5 grams
Mass of oven-dry sample in air for Sample 1 2603.1 grams
Mass of container filled with the sample and water for Sample 1 8959.6 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.489
Theoretical maximum density at 25°C (77°F) 2481.8 kg/m^3

Test 2 of 3

DIME Test ID: 2025-10-22-60-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 11/21/2025
Date Tested: 11/07/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: R1 OBC 4.7%
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of HMA Sample prior to ignition 2146.7 g
Corrected Asphalt Binder Content 4.78 %
Mass Loss 121.9 g
Correction Factor (Percent by mass of HMA Specimen) 0.9 %
Moisture Content no data0 %
Temperature Compensation Factor 0.02 %
Test Temperature 538 C

Test 3 of 3

DIME Test ID: 2025-10-22-60-3
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 11/21/2025
Date Tested: 11/12/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: Passes: A - 24760 B - 24660
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method PMLC
Test Temperature 122 F
Air Void Content for specimen A-1 7 %
Air Void Content for specimen A-2 6.7 %
Air Void Content for specimen B-1 7.2 %
Air Void Content for specimen B-2 7.2 %
Stripping Inflection Point (Wheel A) 25000
Stripping Inflection Point (Wheel B) 25000
Maximum impression at 5000 passes (left wheel) 1.23 mm
Maximum impression at 5000 passes (right wheel) 1.1 mm
Average impression at 5000 passes (left/right avg) 1.17 mm
Maximum impression at 10000 passes (left wheel) 1.53 mm
Maximum impression at 10000 passes (right wheel) 1.36 mm
Average impression at 10000 passes (left/right avg) 1.45 mm
Maximum impression at 15000 passes (left wheel) 1.72 mm
Maximum impression at 15000 passes (right wheel) 1.55 mm
Average impression at 15000 passes (left/right avg) 1.64 mm
Maximum impression at 20000 passes (left wheel) 1.86 mm
Maximum impression at 20000 passes (right wheel) 1.71 mm
Average impression at 20000 passes (left/right avg) 1.79 mm
Average impression at 25000 passes (left/right avg) 1.87 mm