Print Report | Back to Sample Detail

Sample Record for 2025-10-23-56

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1001120 DEA: 033G6204 EFIS: 0325000037 QA Service Level: 1
DIST-CO-RTE-PM: 03-YOL-5-R22.8/R28.9
Work Description: COLD PLANE AC PVMT AND HMA (TYPE A).
Location Description: YOLO COUNTY NEAR DUNNIGAN FROM 0.2 MILE NORTH OF ROUTE 505/5 SEPARATION TO THE COLUSA COUNTY LINE
Contractor Name: ALL-AMERICAN CONSTRUCTION, INC.
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2025-10-23-56
TL Number from the TL Form:
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 10/23/2025
Date that the sample was received by the laboratory/organization performing the testing: 11/06/2025
The quantity of what the sample constitutes: 2 Boxes
A brief description of the sample: 3/4" HMA w/ 15% RAP
From where was the sample collected: Source
Laboratory sample identification: Daily 25-255
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert Woodland

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number: 1
Sublot number: 20
HMA Mix Number: 30640432407V
Binder content (%): 4.7
Virgin binder PG:
Design binder PG: PG 64-16
Binder Supplier: Valero
RAP content (%): 15
WMA Additives: No
Antistrip type:
Test results on following page(s): 2

Test Results

Test 1 of 2

DIME Test ID: 2025-10-23-56-1
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 11/20/2025
Date Tested: 11/17/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7402.5 grams
Mass of oven-dry sample in air for Sample 1 2539.1 grams
Mass of container filled with the sample and water for Sample 1 8928.6 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.507
Theoretical maximum density at 25°C (77°F) 2499.7 kg/m^3

Test 2 of 2

DIME Test ID: 2025-10-23-56-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 11/20/2025
Date Tested: 11/19/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: R1 OBC 4.7%
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of HMA Sample prior to ignition 2295.4 g
Corrected Asphalt Binder Content 5.06 %
Mass Loss 136.7 g
Correction Factor (Percent by mass of HMA Specimen) 0.9 %
Moisture Content no data0 %
Temperature Compensation Factor 0.02 %
Test Temperature 538 C