Print Report | Back to Sample Detail

Sample Record for 2025-09-13-7

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1000402 DEA: 11430384 EFIS: 1118000114 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-805-23.7/28.5
Work Description: REPLACE DRAINAGE, CONCRETE PAVEMENT, AND MODIFY ELECTRICAL SYSTEMS.
Location Description: SAN DIEGO COUNTY IN SAN DIEGO FROM 0.1 MILE NORTH OF ROUTE 805/52 SEPARATION TO ROUTE 5/805 SEPARATION
Contractor Name: HAZARD CONSTRUCTION ENGR, LLC
Contractor Address: 10529 VINE STREET, LAKESIDE, CA 92040
Resident Engineer: Karl Hartline Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2025-09-13-7
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Production Start-Up
Type of Material: Hot Mix Asphalt
Sample Taken Date: 09/13/2025
Date that the sample was received by the laboratory/organization performing the testing: 09/15/2025
The quantity of what the sample constitutes: 12 boxes
A brief description of the sample: RPSU
From where was the sample collected: Supplier
Laboratory sample identification: 25-09-13-7-RPSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Martin Marietta

Material Information

HMA Type: RHMA-G
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 21218180AH MM
Binder content (%): 7.5
Virgin binder PG: PG 64-16
Design binder PG: PG 64-16
Binder Supplier: Valero
RAP content (%): 0
WMA Additives: No
Antistrip type: Liquid
Test results on following page(s): 6

Test Results

Test 1 of 6

DIME Test ID: 2025-09-13-7-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/30/2025
Date Tested: 09/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 7.5% - Tested 4.59 %
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 3995.9 g
Mass of the specimen and specimen basket assembly prior to ignition 5543.2 g
Mass of HMA Sample prior to ignition 1547.3 g
Corrected Asphalt Binder Content 7.59 %
Mass Loss 119 g
Mass of aggregate remaining after ignition 1428.3 g
Correction Factor (Percent by mass of HMA Specimen) 0.1 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 482 C

Test 2 of 6

DIME Test ID: 2025-09-13-7-2
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 09/30/2025
Date Tested: 09/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Does Not Comply Target 2.460 - Tested 2 times 1st - 2.419 2nd 2.424
Test Result Compliance: does not comply
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7475.6 grams
Mass of oven-dry sample in air for Sample 1 1534.4 grams
Mass of container filled with the sample and water for Sample 1 8377.1 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.424
Theoretical maximum density at 25°C (77°F) 150.9 lb/ft^3

Test 3 of 6

DIME Test ID: 2025-09-13-7-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 09/30/2025
Date Tested: 09/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target Low and High Gmb within 0.008
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.278
Bulk Specific Gravity 2 2.281
Bulk Specific Gravity 3 2.277
Average Bulk Specific Gravity 2.279

Test 4 of 6

DIME Test ID: 2025-09-13-7-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 09/30/2025
Date Tested: 09/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Does Not Comply - Target 4.0 % +/- 1.5 % Tested an Avg of 6.0%
Test Result Compliance: does not comply
Additional Comments When Verified:
Percent Air Voids 6 %
Percent Air Voids 2 5.9 %
Percent Air Voids 3 6.1 %
Average Percent Air Voids 6 %

Test 5 of 6

DIME Test ID: 2025-09-13-7-5
Test Method: CTM 375-February 2012: Determining the Density and Relative Compaction of Data Cores (lab)
Verified Date: 12/11/2025
Date Tested: 12/05/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of Cores 4
Core 1 ID 1 A
Dry Weight 1 946.8 grams
Parrafin Coated Weight 1 967.6 grams
Coated Weight in Water 1 528.9 grams
Theoretical Maximum Density 2.424
Core 2 ID 1 B
Dry Weight 2 879 grams
Parrafin Coated Weight 2 899.5 grams
Coated Weight in Water 2 489.7 grams
Core 3 ID 1 C
Dry Weight 3 854.5 grams
Parrafin Coated Weight 3 875 grams
Coated Weight in Water 3 473.2 grams
Core 4 ID 2 A
Dry Weight 4 849.2 grams
Parrafin Coated Weight 4 867.4 grams
Coated Weight in Water 4 477.1 grams
Sublot Relative Compaction 93.8 %

Test 6 of 6

DIME Test ID: 2025-09-13-7-6
Test Method: CTM 375-February 2012: Determining the Density and Relative Compaction of Data Cores (lab)
Verified Date: 12/11/2025
Date Tested: 12/05/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of Cores 4
Core 1 ID 2 B
Dry Weight 1 875.5 grams
Parrafin Coated Weight 1 892.5 grams
Coated Weight in Water 1 487.7 grams
Theoretical Maximum Density 2.424
Core 2 ID 2 C
Dry Weight 2 1121.6 grams
Parrafin Coated Weight 2 1144.1 grams
Coated Weight in Water 2 627.6 grams
Core 3 ID 3 A
Dry Weight 3 829.6 grams
Parrafin Coated Weight 3 845.8 grams
Coated Weight in Water 3 467.3 grams
Core 4 ID 3 B
Dry Weight 4 935.5 grams
Parrafin Coated Weight 4 955.3 grams
Coated Weight in Water 4 519.3 grams
Sublot Relative Compaction 94 %