Print Report | Back to Sample Detail

Sample Record for 2025-08-28-62

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1000435 DEA: 030J01U4 EFIS: 0323000244 QA Service Level: 1
DIST-CO-RTE-PM: 03-PLA-28-0.1/11.0
Work Description: HMA (TYPE A), COLD PLANE AC PVMT, RDWY EXC, & CL 2 AB.
Location Description: PLACER COUNTY FROM 0.1 MILE EAST OF ROUTE 89 AT TAHOE CITY TO THE NEVADA STATE LINE AT KINGS BEACH
Contractor Name: MERCER-FRASER COMPANY
Contractor Address: PO Box 1006, Eureka, CA 95502
Resident Engineer: Reza Salehi Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2025-08-28-62
TL Number from the TL Form:
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Production Start-Up
Type of Material: Hot Mix Asphalt
Sample Taken Date: 08/28/2025
Date that the sample was received by the laboratory/organization performing the testing: 09/05/2025
The quantity of what the sample constitutes: 10 Boxes
A brief description of the sample: 1/2" HMA w/ 15% RAP
From where was the sample collected: Source
Laboratory sample identification: PSU 25-169
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert Martis

Material Information

HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number: 1
Sublot number: 1
HMA Mix Number: 30540742407P
Binder content (%): 5.8
Virgin binder PG: PG 64-28
Design binder PG: PG 64-28
Binder Supplier: PNW
RAP content (%): 15
WMA Additives: No
Antistrip type:
Test results on following page(s): 5

Test Results

Test 1 of 5

DIME Test ID: 2025-08-28-62-1
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 09/17/2025
Date Tested: 09/09/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Specific Gravity for Sample 1 2.47
Theoretical maximum density at 25°C (77°F) 2 kg/m^3

Test 2 of 5

DIME Test ID: 2025-08-28-62-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/17/2025
Date Tested: 09/09/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: R1 OBC 5.8%
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of HMA Sample prior to ignition 1727.1 g
Corrected Asphalt Binder Content 5.99 %
Mass Loss 110 g
Correction Factor (Percent by mass of HMA Specimen) 0.38 %
Moisture Content no data0 %
Temperature Compensation Factor 0.02 %
Test Temperature 538 C

Test 3 of 5

DIME Test ID: 2025-08-28-62-3
Test Method: AASHTO T166-16: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens (Method A)
Verified Date: 09/17/2025
Date Tested: 09/15/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 4
Bulk Specific Gravity 1 2.308
Bulk Specific Gravity 2 2.308
Bulk Specific Gravity 3 2.31
Bulk Specific Gravity 4 2.308
Percent of water absorbed by volume 1 0.33 %
Percent of water absorbed by volume 2 0.21 %
Percent of water absorbed by volume 3 0.33 %
Percent of water absorbed by volume 4 0.38 %
Average Bulk Specific Gravity 2.309

Test 4 of 5

DIME Test ID: 2025-08-28-62-4
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 09/17/2025
Date Tested: 09/16/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A) 24780
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B) 24740
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A) 4.59 mm
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B) 3.69 mm
Stripping Inflection Point (Wheel A) 25000
Stripping Inflection Point (Wheel B) 25000

Test 5 of 5

DIME Test ID: 2025-08-28-62-5
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 09/17/2025
Date Tested: 09/10/2025
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method PMLC
Average impression at 5000 passes (left/right avg) 1.465 mm
Average impression at 10000 passes (left/right avg) 1.875 mm
Average impression at 15000 passes (left/right avg) 2.155 mm
Average impression at 20000 passes (left/right avg) 2.365 mm
Average impression at 25000 passes (left/right avg) 2.635 mm