Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 215734 DEA: 024H0104 EFIS: 0218000068
QA Service Level: 1
DIST-CO-RTE-PM: 02-PLU-70-78.3/90.3
Work Description: REPLACE AC SURFACING, PLACE HMA AND THERMOPLASTIC TRAFFIC STRIPING.
Location Description: PLUMAS COUNTY NEAR PORTOLA FROM 0.4 MILE WEST OF BIG GRIZZLY CREEK BRIDGE TO 0.8 MILE WEST OF SUMMIT SCHOOL DRIVE
Contractor Name: HAT CREEK CONSTRUCTION & MATERIALS, INC.
Contractor Address: 243339 Hwy 89, N Burney, CA 96013
Resident Engineer: Mike Zdenek Structure Rep.: Unknown
DIME Sample ID: 2025-07-22-79
TL Number from the TL Form: 815572
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Production Start-Up
Type of Material: Hot Mix Asphalt
Sample Taken Date: 07/22/2025
Date that the sample was received by the laboratory/organization performing the testing: 07/23/2025
The quantity of what the sample constitutes: Production Start-Up Evaluation
A brief description of the sample: Lime Treated 1/2-inch Type A HMAA (eq. PG 64-16)
From where was the sample collected: Manufacturer
Laboratory sample identification: D79971
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Hat Creek Construction and Materials — Ward Lake Plant (Litchfield, CA)
HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number:
Binder content (%): 6.2
Virgin binder PG: PG 58-22
Design binder PG: PG 64-16
Binder Supplier: Albina (Klamath Falls, OR)
RAP content (%): 25
WMA Additives: No
Antistrip type: Lime
DIME Test ID: 2025-07-22-79-1
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/13/2025
Date Tested: 07/23/2025
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Gmm=2.453
Test Result Compliance: not applicable
Additional Comments When Verified:
|
Number of tests
|
1
|
|
What is the unit of measurement for theoretical density?
|
SI Units
|
|
Mass Determination
|
Air
|
|
Method Performed
|
Mechanical Agitation - Method A
|
|
Mass of container filled with water
|
7331.5 grams
|
|
Mass of oven-dry sample in air for Sample 1
|
1541.2 grams
|
|
Mass of container filled with the sample and water for Sample 1
|
8244.5 grams
|
|
Temperature of Water
|
76 °F
|
|
Specific Gravity for Sample 1
|
2.453
|
|
Theoretical maximum density at 25°C (77°F)
|
2445.9 kg/m^3
|
DIME Test ID: 2025-07-22-79-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/13/2025
Date Tested: 08/05/2025
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Pb=5.98%
Test Result Compliance: complies
Additional Comments When Verified:
|
What temperature unit is used?
|
Celsius
|
|
Test procedure used?
|
Method A
|
|
Mass of the specimen basket assembly
|
3039.7 g
|
|
Mass of the specimen and specimen basket assembly prior to ignition
|
4585 g
|
|
Mass of HMA Sample prior to ignition
|
1545.3 g
|
|
Corrected Asphalt Binder Content
|
5.99 %
|
|
Mass Loss
|
108.9 g
|
|
Mass of aggregate remaining after ignition
|
1436.4 g
|
|
Correction Factor (Percent by mass of HMA Specimen)
|
0.87 %
|
|
Moisture Content
|
no data0 %
|
|
Temperature Compensation Factor
|
0.19 %
|
|
Test Temperature
|
538 C
|
DIME Test ID: 2025-07-22-79-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 08/13/2025
Date Tested: 07/31/2025
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Gmb=2.381
Test Result Compliance: not applicable
Additional Comments When Verified:
|
Bulk Specific Gravity
|
2.38
|
|
Bulk Specific Gravity 2
|
2.382
|
|
Bulk Specific Gravity 3
|
2.38
|
|
Average Bulk Specific Gravity
|
2.381
|
DIME Test ID: 2025-07-22-79-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 08/13/2025
Date Tested: 08/01/2025
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: Pa=3.0%
Test Result Compliance: complies
Additional Comments When Verified:
|
Percent Air Voids
|
3 %
|
|
Percent Air Voids 2
|
2.9 %
|
|
Percent Air Voids 3
|
3 %
|
|
Average Percent Air Voids
|
3 %
|
DIME Test ID: 2025-07-22-79-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 08/13/2025
Date Tested: 08/13/2025
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: S1=137 psi, S2=127 psi, TSR=93%
Test Result Compliance: complies
Additional Comments When Verified:
|
Unit system used?
|
SI Units
|
|
Average Dry Tensile Strength
|
137 psi
|
|
Average Wet Tensile Strength
|
127 psi
|
|
Tensile Strength Ratio
|
0.93
|
DIME Test ID: 2025-07-22-79-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 01/29/2026
Date Tested: 08/12/2025
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: CT 360:
SA=0.4g/cm²;
CT 389:
Rut=0.1in.@N₁₅₀₀₀,
Nf>15000,
SIP>15000
Test Result Compliance: complies
Additional Comments When Verified:
|
Specimen Preparation Method
|
PMLC
|
|
Test Temperature
|
122 F
|
|
Air Void Content for specimen A-1
|
6.9 %
|
|
Air Void Content for specimen A-2
|
6.9 %
|
|
Air Void Content for specimen B-1
|
6.9 %
|
|
Air Void Content for specimen B-2
|
7.1 %
|
|
Stripping Inflection Point (Wheel A)
|
>15000
|
|
Stripping Inflection Point (Wheel B)
|
>15000
|
|
Maximum impression at 5000 passes (left wheel)
|
2.2 mm
|
|
Maximum impression at 5000 passes (right wheel)
|
2.46 mm
|
|
Average impression at 5000 passes (left/right avg)
|
2.33 mm
|
|
Maximum impression at 10000 passes (left wheel)
|
2.8 mm
|
|
Maximum impression at 10000 passes (right wheel)
|
2.94 mm
|
|
Average impression at 10000 passes (left/right avg)
|
2.87 mm
|
|
Maximum impression at 15000 passes (left wheel)
|
3.2 mm
|
|
Maximum impression at 15000 passes (right wheel)
|
3.27 mm
|
|
Average impression at 15000 passes (left/right avg)
|
3.24 mm
|
|
Average impression at 20000 passes (left/right avg)
|
no data
|
|
Average impression at 25000 passes (left/right avg)
|
no data
|
DIME Test ID: 2025-07-22-79-7
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 01/29/2026
Date Tested: 07/31/2025
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: AASHTO T 269:
Pₐ=3.0%;
MS-2:
VMA=13.2%,
VFA=77.6%,
DP=1.6
Test Result Compliance: does not comply
Additional Comments When Verified:
|
Percent Air Voids
|
3 %
|
|
Percent Air Voids 2
|
2.9 %
|
|
Percent Air Voids 3
|
3 %
|
|
Average Percent Air Voids
|
3 %
|
