Print Report | Back to Sample Detail

Sample Record for 2025-08-06-43

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1000211 DEA: 112N0204 EFIS: 1117000168 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-76-R17.2/24.1
Work Description: COLD PLANE AND OVERLAY WITH RHMA GAP GRADED.
Location Description: SAN DIEGO COUNTY NEAR PALA FROM ROUTE 76/15 SEPARATION TO PALA MISSION ROAD
Contractor Name: GRIFFITH COMPANY
Contractor Address: 13400 Sabre Spring Parkway Ste 200, San Diego, CA 92128
Resident Engineer: Fahad Masud Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2025-08-06-43
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Production Start-Up
Type of Material: Hot Mix Asphalt
Sample Taken Date: 08/06/2025
Date that the sample was received by the laboratory/organization performing the testing: 08/07/2025
The quantity of what the sample constitutes: 12 Boxes
A brief description of the sample: PSU
From where was the sample collected: Supplier
Laboratory sample identification: 25-08-06-43-PSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Corona

Material Information

HMA Type: RHMA-G
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 326122 CORD SJR
Binder content (%): 7.5
Virgin binder PG: PG 64-16
Design binder PG: PG 64-16
Binder Supplier: SJR
RAP content (%): 0
WMA Additives: Yes
Antistrip type:
Test results on following page(s): 7

Test Results

Test 1 of 7

DIME Test ID: 2025-08-06-43-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 08/27/2025
Date Tested: 08/21/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 7.5%, Saved material for T30 Tested 7.64 %
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4022 g
Mass of the specimen and specimen basket assembly prior to ignition 5552.2 g
Mass of HMA Sample prior to ignition 1530.2 g
Corrected Asphalt Binder Content 7.64 %
Mass Loss 120.6 g
Mass of aggregate remaining after ignition 1409.6 g
Correction Factor (Percent by mass of HMA Specimen) 0.24 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C

Test 2 of 7

DIME Test ID: 2025-08-06-43-2
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/14/2025
Date Tested: 08/13/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 2.436 Gmb Within the 0024 Gmb Spec Tested 2.451 Gmb
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7475.6 grams
Mass of oven-dry sample in air for Sample 1 1523.5 grams
Mass of container filled with the sample and water for Sample 1 8377.6 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.451
Theoretical maximum density at 25°C (77°F) 152.6 lb/ft^3

Test 3 of 7

DIME Test ID: 2025-08-06-43-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 08/14/2025
Date Tested: 08/14/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target Spec is Gmb within 0.008 Gmb Low to High Testes Low - 2.398 Gmb and High - 2.405 Gmd -Complies
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.398
Bulk Specific Gravity 2 2.404
Bulk Specific Gravity 3 2.405
Average Bulk Specific Gravity 2.402

Test 4 of 7

DIME Test ID: 2025-08-06-43-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 08/14/2025
Date Tested: 08/14/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Does Not Comply - Target 4.0 +/- 1.5 Air Voids . Tested an Avg of 2.0 Air Voids - Does Not Comply
Test Result Compliance: does not comply
Additional Comments When Verified:
Percent Air Voids 2.2 %
Percent Air Voids 2 1.9 %
Percent Air Voids 3 1.9 %
Average Percent Air Voids 2 %

Test 5 of 7

DIME Test ID: 2025-08-06-43-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 08/19/2025
Date Tested: 08/19/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Does Not Comply Target WET>70 psi / DRY > 100 psi Tested WET - 64 psi and DRY - 98 psi
Test Result Compliance: does not comply
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 98 psi
Average Wet Tensile Strength 64 psi
Tensile Strength Ratio 0.65

Test 6 of 7

DIME Test ID: 2025-08-06-43-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 08/19/2025
Date Tested: 08/15/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target < 12.7 mm Tested an Avg of 9.91 mm
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method PMLC
Test Temperature 122 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) >15000
Stripping Inflection Point (Wheel B) >15000
Maximum impression at 5000 passes (left wheel) 4.17 mm
Maximum impression at 5000 passes (right wheel) 5.04 mm
Average impression at 5000 passes (left/right avg) 4.61 mm
Maximum impression at 10000 passes (left wheel) 5.59 mm
Maximum impression at 10000 passes (right wheel) 7.78 mm
Average impression at 10000 passes (left/right avg) 6.69 mm
Maximum impression at 15000 passes (left wheel) 6.91 mm
Maximum impression at 15000 passes (right wheel) 12.9 mm
Average impression at 15000 passes (left/right avg) 9.91 mm
Average impression at 20000 passes (left/right avg) no data
Average impression at 25000 passes (left/right avg) no data

Test 7 of 7

DIME Test ID: 2025-08-06-43-7
Test Method: CTM 375-February 2012: Determining the Density and Relative Compaction of Data Cores (lab)
Verified Date: 12/09/2025
Date Tested: 12/05/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of Cores 3
Core 1 ID 1 A
Dry Weight 1 1022.5 grams
Parrafin Coated Weight 1 1041.3 grams
Coated Weight in Water 1 582.5 grams
Theoretical Maximum Density 2.451
Core 2 ID 1 B
Dry Weight 2 749.6 grams
Parrafin Coated Weight 2 767.5 grams
Coated Weight in Water 2 411.3 grams
Core 3 ID 1 C
Dry Weight 3 804.4 grams
Parrafin Coated Weight 3 821.3 grams
Coated Weight in Water 3 449.5 grams
Sublot Relative Compaction 93.1 %