Sample Record for 2025-06-27-51
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 1000683 DEA: 11056404 EFIS: 1124000359
QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-11-0.6/2.7
Work Description: PERFORM GRADING, CONSTRUCT DRAINAGE FACILITIES, SIGNS AND STRIPING.
Location Description: SAN DIEGO COUNTY NEAR SAN DIEGO FROM 0.2 MILE WEST OF SANYO AVENUE UNDERCROSSING TO 0.2 MILE EAST OF SIEMPRE VIVA ROAD OVERCROSSING
Contractor Name: HAZARD CONSTRUCTION ENGR, LLC
Contractor Address: Unknown
Resident Engineer: Steve McMillan Structure Rep.: Unknown
Sample Information
DIME Sample ID: 2025-06-27-51
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Production Start-Up
Type of Material: Aggregate
Sample Taken Date: 06/27/2025
Date that the sample was received by the laboratory/organization performing the testing: 06/27/2025
The quantity of what the sample constitutes: 3 bags
A brief description of the sample: RPSU
From where was the sample collected: Supplier
Laboratory sample identification: 25-06-27-51-RPSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Otay
Material Information
Source Identification (SMARA, name of Pit or Job Site): 91-37-0035
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number:
A detailed description of where the material sample was collected: Plant
Where the material sample would have been placed if not sampled:
Primary Aggregate Nominal Size: 1/2 inch
The concrete mix design number:
Lot number:
Sublot number:
Aggregate Mix Number: 326122 Otay SJR
Test Results
Test 1 of 10
DIME Test ID: 2025-06-27-51-2
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 07/30/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
|
Method
|
1 - Combined Fracture Determination
|
|
Aggregate Size and Fracture Type
|
Coarse 1 and 2 Faced
|
|
Percentage of questionable, coarse, 2 faced particles tested
|
no data0 %
|
|
Percentage of questionable, coarse, 1 faced particles tested
|
no data0 %
|
|
Percentage of fractured, coarse, 2 faced particles tested
|
99 %
|
|
Percentage of fractured, coarse, 1 faced particles tested
|
100 %
|
Test 2 of 10
DIME Test ID: 2025-06-27-51-3
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 07/30/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
|
Method
|
A
|
|
Determination
|
By Number
|
|
Dimensional ratio used
|
5:1
|
|
Weighted percentage of particles (by number) that were flat
|
no data0 %
|
|
Weighted percentage of particles (by number) that were elongated
|
0 %
|
|
Weighted percentage of particles (by number) that were both flat and elongated
|
4.3 %
|
|
Weighted percentage of particles (by number) that were neither flat nor elongated
|
95.7 %
|
Test 3 of 10
DIME Test ID: 2025-06-27-51-4
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 07/30/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Test 4 of 10
DIME Test ID: 2025-06-27-51-9
Test Method: CTM 204-June 2010: Method of Test for Liquid Limit, Plastic Limit and Plasticity Index of Soils (Plasticity Index)
Verified Date: 07/30/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Test 5 of 10
DIME Test ID: 2025-06-27-51-7
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 07/30/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
|
Grading designation
|
C
|
|
Mass of sample on No.12 sieve (after 500 revolutions)
|
4356 grams
|
|
Percent loss after 100 revolutions
|
5 %
|
|
Percent loss after 500 revolutions
|
13 %
|
Test 6 of 10
DIME Test ID: 2025-06-27-51-1
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 07/30/2025
Date Tested: 07/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: does not comply
Additional Comments When Verified:
|
What type of gradation is being tested?
|
Combined Gradation
|
|
Cumulative percent passing the 2 in. sieve
|
100 %
|
|
Cumulative percent passing the 1 1/2 in. sieve
|
100 %
|
|
Cumulative percent passing the 1 in. sieve
|
100 %
|
|
Cumulative percent passing the 3/4 in. sieve
|
100 %
|
|
Cumulative percent passing the 1/2 in. sieve
|
92 %
|
|
Cumulative percent passing the 3/8 in. sieve
|
73 %
|
|
Cumulative percent passing the #4 sieve
|
24 %
|
|
Cumulative percent passing the #8 sieve
|
13 %
|
|
Cumulative percent passing the #16 sieve
|
8 %
|
|
Cumulative percent passing the #30 sieve
|
5 %
|
|
Cumulative percent passing the #50 sieve
|
4 %
|
|
Cumulative percent passing the #100 sieve
|
2 %
|
|
Cumulative percent passing the #200 sieve
|
1.9 %
|
Test 7 of 10
DIME Test ID: 2025-06-27-51-10
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Verified Date: 07/30/2025
Date Tested: 07/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
|
Is an aggregate correction factor used?
|
No
|
|
Cumulative percent passing the 2 in. sieve
|
100 %
|
|
Cumulative percent passing the 1 1/2 in. sieve
|
100 %
|
|
Cumulative percent passing the 1 in. sieve
|
100 %
|
|
Cumulative percent passing the 3/4 in. sieve
|
100 %
|
|
Cumulative percent passing the 1/2 in. sieve
|
95 %
|
|
Cumulative percent passing the 3/8 in. sieve
|
78 %
|
|
Cumulative percent passing the #4 sieve
|
33 %
|
|
Cumulative percent passing the #8 sieve
|
21 %
|
|
Cumulative percent passing the #16 sieve
|
13 %
|
|
Cumulative percent passing the #30 sieve
|
9 %
|
|
Cumulative percent passing the #50 sieve
|
6 %
|
|
Cumulative percent passing the #100 sieve
|
4 %
|
|
Cumulative percent passing the #200 sieve
|
3 %
|
Test 8 of 10
DIME Test ID: 2025-06-27-51-5
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 07/30/2025
Date Tested: 07/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
|
Bulk specific gravity
|
2.651
|
|
Bulk specific gravity (SSD Basis)
|
2.685
|
|
Apparent specific gravity
|
2.745
|
|
Absorption
|
1.3 %
|
Test 9 of 10
DIME Test ID: 2025-06-27-51-6
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 07/30/2025
Date Tested: 07/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
|
Basis for relative density testing
|
Bulk SSD
|
|
Specific Gravity
|
2.725
|
|
Absorption
|
1.2 %
|
Test 10 of 10
DIME Test ID: 2025-06-27-51-8
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 07/30/2025
Date Tested: 07/29/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
|
What test method is performed?
|
Method A
|
|
Bulk dry specific gravity
|
2.651
|
|
Average uncompacted voids
|
46 %
|
