Print Report | Back to Sample Detail

Sample Record for 2025-06-27-50

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 1000683 DEA: 11056404 EFIS: 1124000359 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-11-0.6/2.7
Work Description: PERFORM GRADING, CONSTRUCT DRAINAGE FACILITIES, SIGNS AND STRIPING.
Location Description: SAN DIEGO COUNTY NEAR SAN DIEGO FROM 0.2 MILE WEST OF SANYO AVENUE UNDERCROSSING TO 0.2 MILE EAST OF SIEMPRE VIVA ROAD OVERCROSSING
Contractor Name: HAZARD CONSTRUCTION ENGR, LLC
Contractor Address: Unknown
Resident Engineer: Steve McMillan Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2025-06-27-50
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Production Start-Up
Type of Material: Hot Mix Asphalt
Sample Taken Date: 06/27/2025
Date that the sample was received by the laboratory/organization performing the testing: 06/27/2025
The quantity of what the sample constitutes: 12 boxes
A brief description of the sample: RPSU
From where was the sample collected: Supplier
Laboratory sample identification: 25-06-27-50-RPSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Otay

Material Information

HMA Type: RHMA-G
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 326122 Otay SJR
Binder content (%): 7.8
Virgin binder PG: PG 64-16
Design binder PG: PG 64-16
Binder Supplier: SJR
RAP content (%):
WMA Additives: Yes
Antistrip type:
Test results on following page(s): 4

Test Results

Test 1 of 4

DIME Test ID: 2025-06-27-50-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 07/29/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target - 7.80%, Tested 7.62% Saved sample for T30
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4034.6 g
Mass of the specimen and specimen basket assembly prior to ignition 5603.8 g
Mass of HMA Sample prior to ignition 1569.2 g
Corrected Asphalt Binder Content 7.62 %
Mass Loss 134.9 g
Mass of aggregate remaining after ignition 1434.3 g
Correction Factor (Percent by mass of HMA Specimen) 0.98 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C

Test 2 of 4

DIME Test ID: 2025-06-27-50-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 07/29/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies target - 2.418 Tested 2.419
Test Result Compliance: complies
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7475.6 grams
Mass of oven-dry sample in air for Sample 1 1534.3 grams
Mass of container filled with the sample and water for Sample 1 8375.6 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.419
Theoretical maximum density at 25°C (77°F) 150.6 lb/ft^3

Test 3 of 4

DIME Test ID: 2025-06-27-50-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 07/29/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target Gmb within .008 from lowest to highest. Tested 2.288 to 2.296
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.288
Bulk Specific Gravity 2 2.291
Bulk Specific Gravity 3 2.296
Average Bulk Specific Gravity 2.292

Test 4 of 4

DIME Test ID: 2025-06-27-50-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 07/29/2025
Date Tested: 07/28/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 4.0% +/- 1.5% Tested an AVG of 5.3%
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 5.4 %
Percent Air Voids 2 5.3 %
Percent Air Voids 3 5.1 %
Average Percent Air Voids 5.3 %