Print Report | Back to Sample Detail

Sample Record for 2025-06-26-67

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 44444 DEA: ASCP EFIS: ASCP QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for submitting Sample information for Asphalt Supplier Certification Program.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2025-06-26-67
TL Number from the TL Form:
Sample Submitted By Organization: ABT Group
Sample Organization Contact: (949) 690-1411
Type of Sample: Verification
Type of Material: Asphalt Binder
Sample Taken Date: 06/26/2025
Date that the sample was received by the laboratory/organization performing the testing: 06/26/2025
The quantity of what the sample constitutes: 2 of 2, SPLIT SAMPLE FROM SITE VISIT
A brief description of the sample: Tank 06
From where was the sample collected: Manufacturer
Laboratory sample identification: TK0806262025
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Mojave, CA

Material Information

Performance Grade: PG 58-22
Modified: No
Lot number:
Sublot number:
Tank number: 8
Time of sample:
HMA Supplier:
Certified Asphalt Supplier: Pacific Asphalt Distribution - Mojave CA
Multigrade: Yes
Multigrade Type: PG 58-22 / PG 58-16
Asphalt Binder Mix Number:
Test results on following page(s): 7

Test Results

Test 1 of 7

DIME Test ID: 2025-06-26-67-1
Test Method: AASHTO T315-24: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 07/10/2025
Date Tested: 07/04/2025
Submitted By Organization: ABT Group
Organization Address: NA,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: farzan.kazemi@dot.ca.gov
Organization Phone: (775) 357-4620
General Comments for this Test: OG
Test Result Compliance: complies
Additional Comments When Verified:
Phase Original binder
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.06 %
Stress Amplitude 0.191 kPa
Phase Angle (δ) (for the 10 cycles) 87.9 degree
Complex Modulus (G*) (for the 10 measurements) 1.584 kPa
Test Temperature (Specimen 1) 58.0 C
Dynamic Shear, G*/sin(δ) 1.59 kPa

Test 2 of 7

DIME Test ID: 2025-06-26-67-2
Test Method: AASHTO T315-24: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 07/10/2025
Date Tested: 07/04/2025
Submitted By Organization: ABT Group
Organization Address: NA,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: farzan.kazemi@dot.ca.gov
Organization Phone: (775) 357-4620
General Comments for this Test: RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.05 %
Stress Amplitude 0.377 kPa
Phase Angle (δ) (for the 10 cycles) 85.3 degree
Complex Modulus (G*) (for the 10 measurements) 3.748 kPa
Test Temperature (Specimen 1) 58.0 C
Dynamic Shear, G*/sin(δ) 3.76 kPa

Test 3 of 7

DIME Test ID: 2025-06-26-67-3
Test Method: AASHTO T315-24: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 07/10/2025
Date Tested: 07/05/2025
Submitted By Organization: ABT Group
Organization Address: NA,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: farzan.kazemi@dot.ca.gov
Organization Phone: (775) 357-4620
General Comments for this Test: PAV
Test Result Compliance: complies
Additional Comments When Verified:
Phase PAV residue
Test Plate Diameter 8 mm
Test Gap 2 mm
Test Frequency 10.0 rad/s
Strain Amplitude 1.01 %
Stress Amplitude 55.195 kPa
Phase Angle (δ) (for the 10 cycles) 50.6 degree
Complex Modulus (G*) (for the 10 measurements) 5491.792 kPa
Test Temperature (Specimen 1) 22.0 C
(G*) x sin(δ)= 4244 kPa

Test 4 of 7

DIME Test ID: 2025-06-26-67-4
Test Method: AASHTO T51-22: Standard Method of Test for Ductility of Asphalt Materials (Asphalt Binder)
Verified Date: 07/10/2025
Date Tested: 07/05/2025
Submitted By Organization: ABT Group
Organization Address: NA,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: farzan.kazemi@dot.ca.gov
Organization Phone: (775) 357-4620
General Comments for this Test: DUCT
Test Result Compliance: complies
Additional Comments When Verified:
Is a normal test obtainable? Yes
Number of replicates tested Three
Ductility of test #1 (D1) 150 cm
Ductility of test #2 (D2) 150 cm
Ductility of test #3 (D3) 150 cm
Ductility of sample 150 cm

Test 5 of 7

DIME Test ID: 2025-06-26-67-5
Test Method: AASHTO T240-23: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 07/10/2025
Date Tested: 07/04/2025
Submitted By Organization: ABT Group
Organization Address: NA,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: farzan.kazemi@dot.ca.gov
Organization Phone: (775) 357-4620
General Comments for this Test: MASS CHANGE
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Is mass change correction factor needed? No
Any material loss from containers during heating process/testing? No
Mass of container #1 before test (m1i) 207.161 grams
Mass of container #2 before test (m2i) 207.073 grams
Mass of container #1 after test (m1f) 207.124 grams
Mass of container #2 after test (m2f) 207.024 grams
Average mass change -0.123 percent
Mass of empty container #1 172.142 grams
Mass of empty container #2 172.117 grams

Test 6 of 7

DIME Test ID: 2025-06-26-67-6
Test Method: AASHTO T313-22: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Verified Date: 07/10/2025
Date Tested: 07/05/2025
Submitted By Organization: ABT Group
Organization Address: NA,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: farzan.kazemi@dot.ca.gov
Organization Phone: (775) 357-4620
General Comments for this Test: BBR
Test Result Compliance: complies
Additional Comments When Verified:
Minimum test bath temperature at 240 s -12 C
Maximum test bath temperature at 240 s -12 C
Time of test load application no data HH:MM:SS
File name of test data no data
Time beam in bath no data
Time test started no data HH:MM:SS
Flags issued by software during test no data
Correlation coefficient (R²) no data0
Regression coefficient a no data
Regression coefficient b no data
Regression coefficient c no data
Load at time 0.0 no data0 mN
Deflection at time 0.0 s no data0 µm
Load at time 0.5 s no data0 mN
Deflection at time 0.5 s no data0 µm
Load at 60.0 s no data0 mN
Beam deflection 60.0 s no data0 µm
Measured Stiffness Modulus 60.0 s no data
Estimated Stiffness Modulus 60.0 s 143.5 MPa
Difference between stiffness moduli 60.0 s no data
Estimated m-value 60.0 s 0.363

Test 7 of 7

DIME Test ID: 2025-06-26-67-7
Test Method: AASHTO T316-22: Standard Method of Test for Viscosity Determination of Asphalt Binder Using Rotational Viscometer
Verified Date: 07/10/2025
Date Tested: 07/04/2025
Submitted By Organization: ABT Group
Organization Address: NA,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: farzan.kazemi@dot.ca.gov
Organization Phone: (775) 357-4620
General Comments for this Test: VISCOSITY
Test Result Compliance: complies
Additional Comments When Verified:
Is viscosity reading in cP/Pa-s? Pa-s
Time of test 00:00 HH:MM
Test Temperature 135 C
Speed no data0 rpm
Spindle size .463 in
Torque 12.8 %
Viscosity reading #1 (A) 0.255 Pa-s
Viscosity reading #2 (B) 0.254 Pa-s
Viscosity reading #3 (C) 0.255 Pa-s
Average viscosity 0.255 Pa-s