Sample Record for 2017-07-14-4
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 211797 DEA: 080G8424 EFIS: 0814000184
QA Service Level: 1
DIST-CO-RTE-PM: 08-SBD-15-R107.3
Work Description: UPGRADE EXISTING SAFETY ROADSIDE REST AREAS (SRRA)
Location Description: SAN BERNARDINO COUNTY ABOUT 30 MILES EAST OF BARSTOW AT C.V. KANE SAFETY ROADSIDE REST AREA
Contractor Name: HAL HAYS CONSTRUCTION INC.
Contractor Address: 4181 Latham St., Riverside, CA 92501
Resident Engineer: Khoa Nguyen Structure Rep.: Leonard J Romero
Sample Information
DIME Sample ID: 2017-07-14-4
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 07/14/2017
Date that the sample was received by the laboratory/organization performing the testing: 07/18/2017
The quantity of what the sample constitutes: unknown
A brief description of the sample: 3/4 inch and 1inch hex head bolts
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: R and D Fasteners
Material Information
Rocap Number(s): N/A
Heat Number(s): 2059645 and PL16205614
Nut Mfg. Lot Number(s): N/A
Washer Mfg. Lot Number(s): N/A
Bolt Specification: F1554 gr. 36
Bolt Length(s): varies
Nut Specification: N/A
Washer Specification: N/A
Finish: hot-dip galvanized
Diameter/Size: 3/4" and 1"
Bolt Mfg. Lot Number: 74934/1 and 74934/5
Rocap Test Requirement(s): None
Lubricant Requirements(s): None
Washer Inner Diameter(s):
Test Results
Test 1 of 10
DIME Test ID: 2017-07-14-4-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: F1554 10 deg Wedge
Test Result Compliance:
Additional Comments When Verified:
|
Number of Samples
|
1
|
| Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments | | 1A | F1554 Headed Anchor 3/4\" x 25 1/4\" | 0.334 | 26418 | 117 | 79096 | 61472 | 20532 | F1554 10 deg Wedge |
| |
|
UTM
|
400KIP
|
|
Temperature
|
72
|
Test 2 of 10
DIME Test ID: 2017-07-14-4-2
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: F1554 Headed Bolt 10deg Wedge
Test Result Compliance:
Additional Comments When Verified:
|
Number of Samples
|
1
|
| Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments | | 2A | F1554 Headed Anchor 1\" x 25 3/4\" | 0.606 | 47242 | 210 | 77957 | 59727 | 36194 | F1554 Headed Bolt 10deg Wedge |
| |
|
UTM
|
400KIP
|
|
Temperature
|
72
|
Test 3 of 10
DIME Test ID: 2017-07-14-4-5
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
2059645
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB 36
|
|
Size
|
.750 in
|
|
Bolt Length
|
25.250 in
|
|
Gage Type
|
Pass
|
Test 4 of 10
DIME Test ID: 2017-07-14-4-6
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
2059645
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB 36
|
|
Size
|
.750 in
|
|
Bolt Length
|
25.250 in
|
|
Gage Type
|
Pass
|
Test 5 of 10
DIME Test ID: 2017-07-14-4-7
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1C
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
2059645
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB 36
|
|
Size
|
.750 in
|
|
Bolt Length
|
25.250 in
|
|
Gage Type
|
Pass
|
Test 6 of 10
DIME Test ID: 2017-07-14-4-8
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
2A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
PL16205614
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB36
|
|
Size
|
1 in
|
|
Bolt Length
|
25.750 in
|
|
Gage Type
|
Pass
|
Test 7 of 10
DIME Test ID: 2017-07-14-4-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
2059645
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB 36
|
|
Size
|
.750 in
|
|
Bolt Length
|
25.250 in
|
|
Measurement Average
|
4.37 mils
|
Test 8 of 10
DIME Test ID: 2017-07-14-4-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
2059645
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB 36
|
|
Size
|
.750 in
|
|
Bolt Length
|
25.250 in
|
|
Measurement Average
|
4.33 mils
|
Test 9 of 10
DIME Test ID: 2017-07-14-4-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1C
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
2059645
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB 36
|
|
Size
|
.750 in
|
|
Bolt Length
|
25.250 in
|
|
Measurement Average
|
4.47 mils
|
Test 10 of 10
DIME Test ID: 2017-07-14-4-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 07/24/2017
Date Tested: 07/20/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
2A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
PL16205614
|
|
Mfg. Lot Number
|
no data
|
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
|
Product Markings
|
D AB36
|
|
Size
|
1 in
|
|
Bolt Length
|
25.750 in
|
|
Measurement Average
|
4.38 mils
|
Tests Assigned to this Sample
| DIME Test ID | Test Method | Assigned Date | Test Date | Assigned By | Assigned Lab | Test Comments | Assigned To |
| 2017-07-14-4-3 | ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage) | 07/20/2017 | 07/20/2017 | Fred Saylor | CT HQ - Sacramento Structural Materials Testing Laboratory | | Fred Saylor |
| 2017-07-14-4-4 | ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating) | 07/20/2017 | 07/20/2017 | Fred Saylor | CT HQ - Sacramento Structural Materials Testing Laboratory | | Fred Saylor |
95549555
