Sample Record for 2017-06-15-3
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 212468 DEA: 113A0534 EFIS: 1117000127
QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-75-
Work Description:
Location Description:
Contractor Name: Traffic Development Services
Contractor Address: 207 W Los Angeles Ave. , Ste 252, Moorpark ,CA 93021
Resident Engineer: Trung Minh Tran Structure Rep.: Unknown
Sample Information
DIME Sample ID: 2017-06-15-3
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT HQ - QASI Bay Area Field Office
Sample Organization Contact: (916) 284-6784
Type of Sample: Verification
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 06/15/2017
Date that the sample was received by the laboratory/organization performing the testing: 06/15/2017
The quantity of what the sample constitutes: 2
A brief description of the sample: F1554 gr.55 anchor assembly
From where was the sample collected: Fabricator
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: UIS
Material Information
Rocap Number(s): n/a
Heat Number(s): PL16106308
Nut Mfg. Lot Number(s): 24875, NF15200634
Washer Mfg. Lot Number(s): n/a
Bolt Specification: F1554 gr. 55
Bolt Length(s): 3'-0"
Nut Specification: A563-DH
Washer Specification: n/a
Finish: HDG,plain
Diameter/Size: 1 1/2" x 3'-0"
Bolt Mfg. Lot Number: PL1610630802
Rocap Test Requirement(s): none
Lubricant Requirements(s):
Test Results
Test 1 of 11
DIME Test ID: 2017-06-15-3-1
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 06/23/2017
Date Tested: 06/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
PL16106308
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
YELLOW PAINT
|
Size
|
1.5 in
|
Bolt Length
|
36 in
|
Gage Type
|
Pass
|
Test 2 of 11
DIME Test ID: 2017-06-15-3-2
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/23/2017
Date Tested: 06/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
PL16106308
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
YELLOW PAINT
|
Size
|
1.5 in
|
Bolt Length
|
36 in
|
Measurement Average
|
3.49 mils
|
Test 3 of 11
DIME Test ID: 2017-06-15-3-3
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 06/23/2017
Date Tested: 06/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
24875
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
DH U
|
Size
|
1.5 in
|
Gage Type
|
Pass
|
Test 4 of 11
DIME Test ID: 2017-06-15-3-4
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/23/2017
Date Tested: 06/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
24875
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
DH U
|
Size
|
1.5 in
|
Bolt Length
|
no data in
|
Measurement Average
|
3.43 mils
|
Test 5 of 11
DIME Test ID: 2017-06-15-3-5
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 06/23/2017
Date Tested: 06/23/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Proof Load
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By | 1A | B7605717 | 1 1/2\" | 213440 | 949.41 | Proof Load | Fred |
| |
UTM
|
400KIP
|
Temperature
|
72 F
|
Test 6 of 11
DIME Test ID: 2017-06-15-3-6
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 06/23/2017
Date Tested: 06/23/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Heat Number | Diameter (in) | Area (sqin) | Stress at Offset (psi) | Tensile Strength (psi) | Elongation in 4 x d (%) | Tested By | 1 | PL16106308 | 0.501 | 0.197 | 62820 | 88640 | 26.8 | Brian |
| |
UTM
|
67KIP
|
Temperature
|
72 f
|
Test 7 of 11
DIME Test ID: 2017-06-15-3-7
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 06/23/2017
Date Tested: 06/23/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Heat Number | Diameter (in) | Area (sqin) | Stress at Offset (psi) | Tensile Strength (psi) | Elongation in 4 x d (%) | Tested By | 2 | PL16106308 | 0.502 | 0.198 | 62732 | 87950 | 28.4 | Brian |
| |
UTM
|
67KIP
|
Temperature
|
72 f
|
Test 8 of 11
DIME Test ID: 2017-06-15-3-8
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 07/06/2017
Date Tested: 07/06/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By | 2A | B76-057-17 | 1 1/2\" | 212760 | 946.4 | Nut Proof | Brian |
| |
UTM
|
400KIP
|
Temperature
|
71 F
|
Test 9 of 11
DIME Test ID: 2017-06-15-3-9
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 07/06/2017
Date Tested: 07/06/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By | 2B | B76-057-17 | 1 1/2\" | 214390 | 953.67 | Nut Proof | Brian |
| |
UTM
|
400KIP
|
Temperature
|
71 F
|
Test 10 of 11
DIME Test ID: 2017-06-15-3-10
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 07/06/2017
Date Tested: 07/06/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
2A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
24872-166868
|
Finish Coating
|
Plain
|
Product Markings
|
U DH
|
Size
|
no data in
|
Gage Type
|
Pass
|
Test 11 of 11
DIME Test ID: 2017-06-15-3-11
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 07/06/2017
Date Tested: 07/06/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
2B
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
24872-166868
|
Finish Coating
|
Plain
|
Product Markings
|
U DH
|
Size
|
no data in
|
Gage Type
|
Pass
|