Print Report | Back to Sample Detail

Sample Record for 2024-12-05-48

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 66667 DEA: JMFPP EFIS: 0019000043 QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for submitting Sample information for JMF Prequalification Program.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2024-12-05-48
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Verification
Type of Material: Hot Mix Asphalt
Sample Taken Date: 12/05/2024
Date that the sample was received by the laboratory/organization performing the testing: 12/06/2024
The quantity of what the sample constitutes: 24 BOXES RWMA
A brief description of the sample: JMF-PP
From where was the sample collected: Source
Laboratory sample identification: 1203-JMF
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Otay

Material Information

HMA Type: Not Applicable
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 326122 Otay SJR
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 6

Test Results

Test 1 of 6

DIME Test ID: 2024-12-05-48-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 12/19/2024
Date Tested: 12/17/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 8.70% Tested 8.05%
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4010.6 g
Mass of the specimen and specimen basket assembly prior to ignition 5558.9 g
Mass of HMA Sample prior to ignition 1548.3 g
Corrected Asphalt Binder Content 8.05 %
Mass Loss 137.1 g
Mass of aggregate remaining after ignition 1411.2 g
Correction Factor (Percent by mass of HMA Specimen) 0.8 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C

Test 2 of 6

DIME Test ID: 2024-12-05-48-2
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 12/19/2024
Date Tested: 12/17/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target - 4.425 Tested 4.219
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7475.6 grams
Mass of oven-dry sample in air for Sample 1 1545.2 grams
Mass of container filled with the sample and water for Sample 1 8381.9 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.419
Theoretical maximum density at 25°C (77°F) 150.6 lb/ft^3

Test 3 of 6

DIME Test ID: 2024-12-05-48-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 12/19/2024
Date Tested: 12/17/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 4.0 % Air Void Tested an Avg of 3 - 3.9% Air Void
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.322
Bulk Specific Gravity 2 2.324
Bulk Specific Gravity 3 2.328
Average Bulk Specific Gravity 2.325

Test 4 of 6

DIME Test ID: 2024-12-05-48-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 12/19/2024
Date Tested: 12/17/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 4.0% Air Voids Tested an Avg of 3.9% Air Voids
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 4 %
Percent Air Voids 2 3.9 %
Percent Air Voids 3 3.8 %
Average Percent Air Voids 3.9 %

Test 5 of 6

DIME Test ID: 2024-12-05-48-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 01/17/2025
Date Tested: 12/24/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Does not Comply DRY < 100 psi
Test Result Compliance: does not comply
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 87 psi
Average Wet Tensile Strength 71 psi
Tensile Strength Ratio 0.82

Test 6 of 6

DIME Test ID: 2024-12-05-48-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 12/23/2024
Date Tested: 12/20/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target < 12.7 mm Tested 4.70 mm Avg
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 122 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) >20000
Stripping Inflection Point (Wheel B) >20000
Maximum impression at 5000 passes (left wheel) 1.3 mm
Maximum impression at 5000 passes (right wheel) 1.05 mm
Average impression at 5000 passes (left/right avg) 1.18 mm
Maximum impression at 10000 passes (left wheel) 2.6 mm
Maximum impression at 10000 passes (right wheel) 2.1 mm
Average impression at 10000 passes (left/right avg) 2.35 mm
Maximum impression at 15000 passes (left wheel) 3.9 mm
Maximum impression at 15000 passes (right wheel) 3.15 mm
Average impression at 15000 passes (left/right avg) 3.53 mm
Maximum impression at 20000 passes (left wheel) 5.21 mm
Maximum impression at 20000 passes (right wheel) 4.18 mm
Average impression at 20000 passes (left/right avg) 4.7 mm
Average impression at 25000 passes (left/right avg) no data