Print Report | Back to Sample Detail

Sample Record for 2024-11-07-56

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 995482 DEA: 112T36U4 EFIS: 1122000243 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-5-37.4-52.6
Work Description: I-5 NCC SEGMENT 4C
Location Description: I-5 in San Diego County at Various Locations from Lomas Santa Fe Drive Undercrossing to 0.2 Mile North of Oceanside Undercrossing
Contractor Name: Flatiron-Skanska-Stacy and Witbeck Joint Venture
Contractor Address: 1770 La Costa Meadows Drive, San Marcos, CA 92078
Resident Engineer: Yong Pak Structure Rep.: Phong Le

Sample Information

DIME Sample ID: 2024-11-07-56
TL Number from the TL Form:
Sample Submitted By Organization: CT D11 - District 11 Materials Laboratory
Sample Organization Contact: (858) 518-8709
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 11/07/2024
Date that the sample was received by the laboratory/organization performing the testing: 12/05/2024
The quantity of what the sample constitutes: 36 boxes
A brief description of the sample: PSU
From where was the sample collected: Supplier
Laboratory sample identification: 0613-PSU
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan CC

Material Information

HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 320819 CC SJR
Binder content (%):
Virgin binder PG:
Design binder PG:
Binder Supplier:
RAP content (%):
WMA Additives:
Antistrip type:
Test results on following page(s): 8

Test Results

Test 1 of 8

DIME Test ID: 2024-11-07-56-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 01/23/2025
Date Tested: 01/10/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Target = 5.2 Tested 5.56
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 4015.9 g
Mass of the specimen and specimen basket assembly prior to ignition 5575.4 g
Mass of HMA Sample prior to ignition 1559.5 g
Corrected Asphalt Binder Content 5.56 %
Mass Loss 99.1 g
Mass of aggregate remaining after ignition 1460.4 g
Correction Factor (Percent by mass of HMA Specimen) 0.79 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C

Test 2 of 8

DIME Test ID: 2024-11-07-56-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 12/16/2024
Date Tested: 12/12/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 2.478 Tested 2.464
Test Result Compliance: complies
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 1 7475.6 grams
Mass of oven-dry sample in air for Sample 1 1532.6 grams
Mass of container filled with the sample and water for Sample 1 8386.2 grams
Temperature of Water no data0 °F
Specific Gravity for Sample 1 2.464
Theoretical maximum density at 25°C (77°F) 153.4 lb/ft^3

Test 3 of 8

DIME Test ID: 2024-11-07-56-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 12/16/2024
Date Tested: 12/12/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 4.0 , +/- 1.5 % Tested 4.2% Avg of 3
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.361
Bulk Specific Gravity 2 2.362
Bulk Specific Gravity 3 2.357
Average Bulk Specific Gravity 2.36

Test 4 of 8

DIME Test ID: 2024-11-07-56-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 12/16/2024
Date Tested: 12/12/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target 4.0% Tested 4.2%
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 4.2 %
Percent Air Voids 2 4.1 %
Percent Air Voids 3 4.3 %
Average Percent Air Voids 4.2 %

Test 5 of 8

DIME Test ID: 2024-11-07-56-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 01/23/2025
Date Tested: 12/19/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target WET> 70 and DRY>100 Tensile> .50
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 211 psi
Average Wet Tensile Strength 117 psi
Tensile Strength Ratio 0.55

Test 6 of 8

DIME Test ID: 2024-11-07-56-6
Test Method: CTM 389-19: Method of Test for Hamburg Wheel-Track Testing of Compacted Hot Mix Asphalt
Verified Date: 12/16/2024
Date Tested: 12/13/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: Complies Target < 12.7 mm Tested 2.01 mm Avg
Test Result Compliance: complies
Additional Comments When Verified:
Specimen Preparation Method no data
Test Temperature 122 F
Air Void Content for specimen A-1 no data
Air Void Content for specimen A-2 no data
Air Void Content for specimen B-1 no data
Air Void Content for specimen B-2 no data
Stripping Inflection Point (Wheel A) >15000
Stripping Inflection Point (Wheel B) >15000
Maximum impression at 5000 passes (left wheel) 0.94 mm
Maximum impression at 5000 passes (right wheel) 2.04 mm
Average impression at 5000 passes (left/right avg) 1.49 mm
Maximum impression at 10000 passes (left wheel) 1.07 mm
Maximum impression at 10000 passes (right wheel) 2.52 mm
Average impression at 10000 passes (left/right avg) 1.8 mm
Maximum impression at 15000 passes (left wheel) 1.23 mm
Maximum impression at 15000 passes (right wheel) 2.79 mm
Average impression at 15000 passes (left/right avg) 2.01 mm
Average impression at 20000 passes (left/right avg) no data
Average impression at 25000 passes (left/right avg) no data

Test 7 of 8

DIME Test ID: 2024-11-07-56-7
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 12/19/2024
Date Tested: 12/17/2024
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: RAP Gradation
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 3983.7 g
Mass of the specimen and specimen basket assembly prior to ignition 5633.4 g
Mass of HMA Sample prior to ignition 1649.7 g
Corrected Asphalt Binder Content 7.18 %
Mass Loss 118.4 g
Mass of aggregate remaining after ignition 1531.3 g
Correction Factor (Percent by mass of HMA Specimen) no data0 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C

Test 8 of 8

DIME Test ID: 2024-11-07-56-8
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 01/23/2025
Date Tested: 01/02/2025
Submitted By Organization: CT D11 - District 11 Materials Laboratory
Organization Address: 4050 Taylor Street,
Organization City: San Diego
Organization State: CA
Organization Zipcode: 92110
Organization Email: benjamin.haney@dot.ca.gov
Organization Phone: (858) 688-1595
General Comments for this Test: 308 RAP Burn 320819 CC SJR use 7.18% for Blanks
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of the specimen basket assembly 3983.7 g
Mass of the specimen and specimen basket assembly prior to ignition 5633.4 g
Mass of HMA Sample prior to ignition 1649.7 g
Corrected Asphalt Binder Content 7.18 %
Mass Loss 118.4 g
Mass of aggregate remaining after ignition 1531.3 g
Correction Factor (Percent by mass of HMA Specimen) no data0 %
Moisture Content no data0 %
Temperature Compensation Factor no data0 %
Test Temperature 538 C