Print Report | Back to Sample Detail

Sample Record for 2024-11-08-37

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214697 DEA: 07307104 EFIS: 0714000213 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-101-32.8
Work Description: CONSTRUCT BRIDGE.
Location Description: LOS ANGELES COUNTY IN AND NEAR AGOURA HILLS FROM 0.1 MILE WEST OF LIBERTY CANYON ROAD UNDERCROSSING TO 0.6 MILE EAST OF PALO COMADO OVERCROSSING
Contractor Name: CA Rasmussen
Contractor Address: 28548 LIVINGSTON AVENUE, VALENICA CA 91355
Resident Engineer: Sam Toutounchian Structure Rep.: Darwin Vargas

Sample Information

DIME Sample ID: 2024-11-08-37
TL Number from the TL Form:
Sample Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Sample Organization Contact: 213-792-4794
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 11/08/2024
Date that the sample was received by the laboratory/organization performing the testing: 11/13/2024
The quantity of what the sample constitutes: 4 Bags of comb agg (3/4", 1/2", 3/8", state sand, rock dust), 1 bag each of CRM Scrap and Hi-Nat
A brief description of the sample: JMF 3/4" RHMA-G-SP 0.5% LAS
From where was the sample collected: Manufacturer
Laboratory sample identification: 0621G-24
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Ingevity, Valero, Fish Canyon Irwindale

Material Information

Source Identification (SMARA, name of Pit or Job Site): 91-19-0035
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number:
A detailed description of where the material sample was collected: Vulcan Sun Valley
Where the material sample would have been placed if not sampled: Asphalt Paving
Primary Aggregate Nominal Size: 3/4 inch
The concrete mix design number: 226108M SVA VLO
Lot number:
Sublot number:
Aggregate Mix Number:

Test Results

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
2024-11-08-37-1AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-2CTM 202-November 2011: Method of Test for Sieve Analysis of Fine and Coarse Aggregates11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-3CTM 202-November 2011: Method of Test for Sieve Analysis of Fine and Coarse Aggregates11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-4AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-5AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-6AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-7AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-8AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-9AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory
2024-11-08-37-10ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)11/15/2024Not scheduledRonica BhuyianCT D08 - Fontana Southern Regional Laboratory